A critical examination of pure tantalum processed by high-pressure torsion

被引：44

作者：

Maury, Nicolas ^{[1
]}

Zhang, Nian Xian ^{[2
]}

Huang, Yi ^{[2
]}

Zhilyaev, Alexander P. ^{[3
,4
]}

Langdon, Terence G. ^{[2
,5
,6
]}

机构：

[1] INPT, ENSIACET, F-31077 Toulouse 04, France

[2] Univ Southampton, Fac Engn & Environm, Mat Res Grp, Southampton SO17 1BJ, Hants, England

[3] Russian Acad Sci, Inst Met Supeiplast Problems, Ufa 450001, Russia

[4] St Petersburg State Polytech Univ, Res Lab Mech New Nanomat, St Petersburg 195251, Russia

[5] Univ So Calif, Dept Aerosp & Mech Engn, Los Angeles, CA 90089 USA

[6] Univ So Calif, Dept Mat Sci, Los Angeles, CA 90089 USA

来源：

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2015年 / 638卷

基金：

欧洲研究理事会; 俄罗斯科学基金会;

关键词：

Electron backscatter diffraction; Hardness; High-pressure torsion; Tantalum; Ultrafine grains; SEVERE PLASTIC-DEFORMATION; ULTRAFINE-GRAINED MATERIALS; STACKING-FAULT ENERGY; ATOMIC BOND PARAMETERS; MECHANICAL-PROPERTIES; DEFORMED TANTALUM; THERMAL-STABILITY; CUBIC METALS; REFINEMENT; ALLOY;

D O I：

10.1016/j.msea.2015.04.053

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

Tantalum, a common refractory metal with body-centred cubic (BCC) crystalline structure, was processed by high-pressure torsion (HPT) at room temperature through different numbers of rotations. Significant grain refinement and high strength were achieved with a reduction in grain size from similar to 60 mu m to similar to 160 nm and an increase in strength from similar to 200 to > 1300 MPa. Hardness measurements revealed a high level of homogeneity after 10 turns of HPT but the hardness after 10 turns was slightly lower than after 5 turns indicating the occurrence of some recovery. Tensile testing at a strain rate of 1.0 x 10(-3) s(-1) gave high strengths of similar to 1200 MPa but little or no ductility after processing through 1, 5 and 10 turns. The introduction of a short-term (15 min) anneal immediately after HPT processing led to significant ductility in all samples and a reasonable level of strength at similar to 800 MPa. (C) 2015 Elsevier B.V. All rights reserved.

引用

页码：174 / 182

页数：9

共 50 条

[21] An examination of the saturation microstructures achieved in ultrafine-grained metals processed by high-pressure torsion
Sabbaghianrad, Shima
Wongsa-Ngam, Jittraporn
Kawasaki, Megumi
Langdon, Terence G.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2014, 3 (04): : 319 - 326
[22] Correlation of Physical Parameters with Steady-State Hardness of Pure Metals Processed by High-Pressure Torsion
Edalati, Kaveh
Horita, Zenji
NANOMATERIALS BY SEVERE PLASTIC DEFORMATION: NANOSPD5, PTS 1 AND 2, 2011, 667-669 : 683 - 688
[23] Significance of homologous temperature in softening behavior and grain size of pure metals processed by high-pressure torsion
Edalati, Kaveh
Horita, Zenji
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2011, 528 (25-26): : 7514 - 7523
[24] Effect of grain size on the micro-tribological behavior of pure titanium processed by high-pressure torsion
Wang, Chuan Ting
Gao, Nong
Gee, Mark G.
Wood, Robert J. K.
Langdon, Terence G.
WEAR, 2012, 280 : 28 - 35
[25] Tribological behavior of high-pressure torsion processed biodegradable pure Zn under dry and wet conditions
Bulutsuz, Asli Gunay
INDUSTRIAL LUBRICATION AND TRIBOLOGY, 2022, 74 (05) : 542 - 549
[26] An examination of the elastic distortions of anvils in high-pressure torsion
Pereira, Pedro Henrique R.
Figueiredo, Roberto B.
Cetlin, Paulo R.
Langdon, Terence G.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2015, 631 : 201 - 208
[27] Microstructure and microhardness of OFHC copper processed by high-pressure torsion
Almazrouee, Abdulla I.
Al-Fadhalah, Khaled J.
Alhajeri, Saleh N.
Langdon, Terence G.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2015, 641 : 21 - 28
[28] An Evaluation of Homogeneity and Heterogeneity in Metals Processed by High-Pressure Torsion
Figueiredo, R. B.
Kawasaki, M.
Langdon, T. G.
ACTA PHYSICA POLONICA A, 2012, 122 (03) : 425 - 429
[29] Review: achieving superplasticity in metals processed by high-pressure torsion
Kawasaki, Megumi
Langdon, Terence G.
JOURNAL OF MATERIALS SCIENCE, 2014, 49 (19) : 6487 - 6496
[30] On the thermal evolution of high-pressure torsion processed titanium aluminide
Liss, Klaus-Dieter
Liu, Xiaojing
Li, Xi
Han, Jae-Kyung
Dippenaar, Rian J.
Kawasaki, Megumi
MATERIALS LETTERS, 2021, 304

← 1 2 3 4 5 →