Influence of post-machining thermal treatment on the corrosion behaviour of copper

被引：3

作者：

Bissey-Breton, Stephanie ^{[1
,3
]}

Vignal, Vincent ^{[2
,3
]}

机构：

[1] CEA, DAM, F-21120 Valduc, Is Sur Tille, France

[2] Univ Bourgogne, CNRS, UMR 6303, ICB, F-21078 Dijon, France

[3] LRC Nr DAM VA 11 02, LIMPE Interact Mat Proc Environm, Krakow, Poland

来源：

2ND CIRP CONFERENCE ON SURFACE INTEGRITY (CSI) | 2014年 / 13卷

关键词：

machining; hardness; microstructure; corrosion; RESIDUAL-STRESSES; STAINLESS-STEEL; MICROSTRUCTURAL CHANGES; SURFACE INTEGRITY; HARDENED STEEL; FATIGUE LIFE; PARAMETERS;

D O I：

10.1016/j.procir.2014.04.021

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

In this paper, the influence of a post-machining thermal treatment (PMTT) on the corrosion behaviour of copper was investigated in a salt fog atmosphere. The corrosion behaviour was affected by the presence of a high density of grain boundaries generated during machining or dislocations formed during PMTT under certain conditions. The obtained results showed that it is possible to find PMTT conditions to cancel changes induced by machining and that the critical factor leading to a sharp increase of the percentage of oxidized surface seems to be the density of dislocations near the machined surface. (C) 2014 The Authors. Published by Elsevier B.V.

引用

页码：120 / 124

页数：5

共 25 条

[1] Ab Rashid M.F.F., 2010, WCE 2010, VIII, P2219
[2] Turning and grinding as a source of microstructural changes in the surface layer of hardened steel
Barbacki, A
Kawalec, M
Hamrol, A
[J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2003, 133 (1-2) : 21 - 25
[3] The effect of machining on the fatigue strength of a gamma titanium aluminide intertmetallic alloy
Bentley, SA
Mantle, AL
Aspinwall, DK
[J]. INTERMETALLICS, 1999, 7 (08) : 967 - 969
[4] Bunge H., 1982, TEXTURE ANAL MAT SCI, P1, DOI 10.1016/B978-0-408-10642-9.50006-4
[5] Residual stresses in turning - Part I Influence of process parameters
Capello, E
[J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2005, 160 (02) : 221 - 228
[6] Evidence and analysis of thermal static strain aging in the deformed surface zone of finish-machined hardened steel
Gegner, Juergen
Schlier, Lorenz
Nierlich, Wolfgang
[J]. POWDER DIFFRACTION, 2009, 24 (02) : S45 - S50
[7] Microstructural changes in AISI 304L stainless steel due to surface machining: Effect on its susceptibility to chloride stress corrosion cracking
Ghosh, Swati
Kain, Vivekanand
[J]. JOURNAL OF NUCLEAR MATERIALS, 2010, 403 (1-3) : 62 - 67
[8] The effects of cutting tool geometry and processing parameters on the surface roughness of AISI 1030 steel
Gokkaya, Hasan
Nalbant, Muammer
[J]. MATERIALS & DESIGN, 2007, 28 (02) : 717 - 721
[9] The use of linear regression methods and Pearson's correlation matrix to identify mechanical-physical-chemical parameters controlling the micro-electrochemical behaviour of machined copper
Gravier, J.
Vignal, V.
Bissey-Breton, S.
Farre, J.
[J]. CORROSION SCIENCE, 2008, 50 (10) : 2885 - 2894
[10] Influence of residual stress, surface roughness and crystallographic texture induced by machining on the corrosion behaviour of copper in salt-fog atmosphere
Gravier, J.
Vignal, V.
Bissey-Breton, S.
[J]. CORROSION SCIENCE, 2012, 61 : 162 - 170

← 1 2 3 →