Interactive Haptic Refinement of a Five-Axis Finishing Cut

被引：1

作者：

Chen, Kun ^{[1
]}

Tang, Kai ^{[1
]}

机构：

[1] Hong Kong Univ Sci & Technol, Dept Engn Mech, Kowloon, Hong Kong, Peoples R China

来源：

JOURNAL OF COMPUTING AND INFORMATION SCIENCE IN ENGINEERING | 2008年 / 8卷 / 04期

关键词：

haptic design; five-axis; collision-free; tool-path generation;

D O I：

10.1115/1.2987400

中图分类号：

TP39 [计算机的应用];

学科分类号：

081203 ; 0835 ;

摘要：

This paper describes the design of a haptic system that allows the interactive modification of cutter orientation during five-axis finishing cuts with the aim of improving the surface finish quality and collision avoidance strategies. The system supports two haptic models that provide three degree of freedom (DOF) force feedback and 6DOF posture sensing. Details of five key functions of the system are given: (1) a rendering conversion that uses 3DOF (instead of five) force feedback haptic representation, (2) an efficient force feedback design that allows accurate results to be obtained from the user's manipulation, (3) a fast collision detection scheme that achieves real-time feedback, (4) use of active haptic guidance to assist cutter-path generation, and (5) a design that supports both ball-end and flat-end tools with partial optimization. [DOI: 10.1115/1.2987400]

引用

页码：0410011 / 0410017

页数：7

共 24 条

[1] Generation of collision-free 5-axis tool paths using a haptic surface [J].

Balasubramaniam, M ;

Ho, S ;

Sarma, S ;

Adachi, Y .

COMPUTER-AIDED DESIGN, 2002, 34 (04) :267-279

[2] On the development of a haptic system for rapid product development [J].

Chen, YH ;

Yang, ZY ;

Lian, LL .

COMPUTER-AIDED DESIGN, 2005, 37 (05) :559-569

[3] Towards a haptic virtual coordinate measuring machine [J].

Chen, YH ;

Wang, YZ ;

Yang, ZY .

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2004, 44 (10) :1009-1017

[4] A machining potential field approach to tool path generation for multi-axis sculptured surface machining [J].

Chiou, CJ ;

Lee, YS .

COMPUTER-AIDED DESIGN, 2002, 34 (05) :357-371

[5] A shape-generating approach for multi-axis machining G-buffer models [J].

Chiou, CJ ;

Lee, YS .

COMPUTER-AIDED DESIGN, 1999, 31 (12) :761-776

[6] Floor, wall and ceiling approach for ball-end tool pocket machining [J].

Chiou, JCJ .

COMPUTER-AIDED DESIGN, 2005, 37 (04) :373-385

[7] Accurate tool position for five-axis ruled surface machining by swept envelope approach [J].

Chiou, JCJ .

COMPUTER-AIDED DESIGN, 2004, 36 (10) :967-974

[8] CUTTER-LOCATION DATA OPTIMIZATION IN 5-AXIS SURFACE MACHINING [J].

CHOI, BK ;

PARK, JW ;

JUN, CS .

COMPUTER-AIDED DESIGN, 1993, 25 (06) :377-386

[9]

Choi BK, 1998, SCULPTURED SURFACE M

[10]

Cignoni P., 1993, Computer Graphics Forum, V12, pC129, DOI 10.1111/1467-8659.1230129

← 1 2 3 →