Effect of adding method of Cr on microstructure and properties of WC-9Ni-2Cr cemented carbides

被引：19
作者：
Shi Kai-hua [1 ]
Zhou Ke-chao [1 ]
Li Zhi-you [1 ]
Zan Xiu-qi [2 ]
Xu Shang-zhi [2 ]
Min Zhao-yu [2 ]
机构：
[1] Cent S Univ, State Key Lab Powder Met, Changsha 410083, Hunan, Peoples R China
[2] Zi Gong Cemented Carbide Corp Ltd, Zigong 643011, Peoples R China
来源：
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS | 2013年 / 38卷
关键词：
Cemented carbides; Chromium; Microstructure; Properties; WC-CO; CORROSION; FRICTION; BEHAVIOR; CR3C2; VC;
D O I：
10.1016/j.ijrmhm.2012.11.010
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
The WC-9Ni-2Cr cemented carbides were prepared by ball milling method and low pressure sintering. The microstructure and properties of the cemented carbides were then investigated using scanning electron microscopy, mechanical property tester and immersion corrosion tests. The results showed that the adding method of Cr significantly influenced the microstructure and properties of the WC-9Ni-2Cr cemented carbides. Cemented carbides with Cr added in the form of chromium carbide (Cr3C2) were characterized by carburizing and showed a relative lower density, while the addition of metallic chromium and nichrome (Ni-18Cr) resulted in the formation of (W,Cr)C phase and a decrease in the bending strength. However, no defects were found in the microstructure of the cemented carbides in which Cr was added via Cr-Cr3C2 composite powder. Furthermore, cemented carbides prepared with nichrome powder and metallic Cr powder exhibited a higher immersion corrosion resistance in neutral tap water after soaking six times according to BS:6920:2000. (C) 2012 Elsevier Ltd. All rights reserved.
引用
收藏
页码：1 / 6
页数：6
相关论文
共 22 条
  • [1] Liquid phase sintering and oxidation resistance of WC-Ni-Co-Cr cemented carbides
    Aristizabal, M.
    Rodriguez, N.
    Ibarreta, F.
    Martinez, R.
    Sanchez, J. M.
    [J]. INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS, 2010, 28 (04) : 516 - 522
  • [2] Fabrication of full density near-nanostructured cemented carbides by combination of VC/Cr3C2 addition and consolidation by SPS and HIP technologies
    Bonache, V.
    Salvador, M. D.
    Fernandez, A.
    Borrell, A.
    [J]. INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS, 2011, 29 (02) : 202 - 208
  • [3] Impact of Cr3C2/VC addition on the dry sliding friction and wear response of WC-Co cemented carbides
    Bonny, K.
    De Baets, P.
    Vleugels, J.
    Huang, S.
    Van der Biest, O.
    Lauwers, B.
    [J]. WEAR, 2009, 267 (9-10) : 1642 - 1652
  • [4] Diffusion and solubility of Cr in WC
    Brieseck, M.
    Bohn, M.
    Lengauer, W.
    [J]. JOURNAL OF ALLOYS AND COMPOUNDS, 2010, 489 (02) : 408 - 414
  • [5] Chen Jianzhong, 2009, CEMENTED CARBIDE, V26, P212
  • [6] Friction and wear behaviour of WC-Co-Cr3C2-VC cemented carbides obtained from nanocrystalline mixtures
    Espinosa, L.
    Bonache, V.
    Salvador, M. D.
    [J]. WEAR, 2011, 272 (01) : 62 - 68
  • [7] Synthesis, sintering, and mechanical properties of nanocrystalline cemented tungsten carbide - A review
    Fang, Z. Zak
    Wang, Xu
    Ryu, Taegong
    Hwang, Kyu Sup
    Sohn, H. Y.
    [J]. INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS, 2009, 27 (02) : 288 - 299
  • [8] Rotating wheel abrasion of WC/Co hardmetals
    Gant, AJ
    Gee, MG
    Roebuck, B
    [J]. WEAR, 2005, 258 (1-4) : 178 - 188
  • [9] Analytical characterization of the corrosion mechanisms of WC-Co by electrochemical methods and inductively coupled plasma mass spectroscopy
    Hochstrasser-Kurz, S.
    Mueller, Y.
    Latkoczy, C.
    Virtanen, S.
    Schmutz, P.
    [J]. CORROSION SCIENCE, 2007, 49 (04) : 2002 - 2020
  • [10] Hu DP, 2006, CORROS PROT, V27, P382
123