Fatigue strength of notched specimens made of Ti-6Al-4V produced by Selected Laser Melting technique

被引：15

作者：

Razavi, N. ^{[1
]}

Berto, F. ^{[1
]}

机构：

[1] Norwegian Univ Sci & Technol NTNU, Dept Mech & Ind Engn, N-7491 Trondheim, Norway

来源：

ECF22 - LOADING AND ENVIRONMENTAL EFFECTS ON STRUCTURAL INTEGRITY | 2018年 / 13卷

关键词：

Fatigue; Notch Mechanics; Selective Laser Melting (SLM); Semi-circular notch; V notch; MICROSTRUCTURE; ALLOY;

D O I：

10.1016/j.prostr.2018.12.013

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

As an Additive Manufacturing (AM) method, Selective Laser Melting (SLM) allows fabrication of metallic components of any desired geometry with densities greater than 99.5%. This method is usually used for geometrically optimized components with complex geometries including various kinds of notches. Hence, it is important to have a clear information about the fatigue behavior of notched components made by SLM method. This paper evaluates the fatigue behavior of Ti-6A1-4V blunt V-notched and circular notched samples produced by SLM. The fatigue results were then compared with those of the corresponding smooth samples. The fracture surfaces of the tested samples were evaluated using Environmental Scanning Electron Microscopy (ESEM) and the crack initiation points and fracture mechanisms were identified. (C) 2018 The Authors. Published by Elsevier B.V.

引用

页码：74 / 78

页数：5

共 18 条

[11] RETRACTED: Fatigue Assessment of Ti-6Al-4V Circular Notched Specimens Produced by Selective Laser Melting (Retracted article. See vol. 46, artn. 291, 2017) [J].

Razavi, Seyed-Mohammad-Javad ;

Ferro, Paolo ;

Berto, Filippo .

METALS, 2017, 7 (08)

[12]

Riemer A., 2015, FRATTURA INTEGRITA S, V34, P437, DOI DOI 10.3221/IGF-ESIS.34.49

[13] Microstructure and fatigue behaviors of a biomedical Ti-Nb-Ta-Zr alloy with trace CeO2 additions [J].

Song, Xiu ;

Wang, Lei ;

Niinomi, Mitsuo ;

Nakai, Masaaki ;

Liu, Yang ;

Zhu, Miaoyong .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2014, 619 :112-118

[14] Fatigue performance of additive manufactured metallic parts [J].

Spierings, A. B. ;

Starr, T. L. ;

Wegener, K. .

RAPID PROTOTYPING JOURNAL, 2013, 19 (02) :88-94

[15] Fatigue properties of a biomedical 316L steel processed by surface mechanical attrition [J].

Sun, Z. ;

Chemkhi, M. ;

Kanoute, P. ;

Retraint, D. .

6TH INTERNATIONAL CONFERENCE ON NANOMATERIALS BY SEVERE PLASTIC DEFORMATION (NANOSPD6), 2014, 63

[16] Effect of building direction on the microstructure and tensile properties of Ti-48Al-2Cr-2Nb alloy additively manufactured by electron beam melting [J].

Todai, Mitsuharu ;

Nakano, Takayoshi ;

Liu, Tianqi ;

Yasuda, Hiroyuki Y. ;

Hagihara, Koji ;

Cho, Ken ;

Ueda, Minoru ;

Takeyama, Masao .

ADDITIVE MANUFACTURING, 2017, 13 :61-70

[17] Microstructures of laser-deposited Ti-6Al-4V [J].

Wu, XH ;

Jing, LA ;

Mel, JF ;

Mitchell, C ;

Goodwin, PS ;

Voice, W .

MATERIALS & DESIGN, 2004, 25 (02) :137-144

[18] Additive manufacturing of fatigue resistant materials: Challenges and opportunities [J].

Yadollahi, Aref ;

Shamsaei, Nima .

INTERNATIONAL JOURNAL OF FATIGUE, 2017, 98 :14-31

← 1 2 →