Fatigue strength of notched specimens made of Ti-6Al-4V produced by Selected Laser Melting technique

被引：15

作者：

Razavi, N. ^{[1
]}

Berto, F. ^{[1
]}

机构：

[1] Norwegian Univ Sci & Technol NTNU, Dept Mech & Ind Engn, N-7491 Trondheim, Norway

来源：

ECF22 - LOADING AND ENVIRONMENTAL EFFECTS ON STRUCTURAL INTEGRITY | 2018年 / 13卷

关键词：

Fatigue; Notch Mechanics; Selective Laser Melting (SLM); Semi-circular notch; V notch; MICROSTRUCTURE; ALLOY;

D O I：

10.1016/j.prostr.2018.12.013

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

As an Additive Manufacturing (AM) method, Selective Laser Melting (SLM) allows fabrication of metallic components of any desired geometry with densities greater than 99.5%. This method is usually used for geometrically optimized components with complex geometries including various kinds of notches. Hence, it is important to have a clear information about the fatigue behavior of notched components made by SLM method. This paper evaluates the fatigue behavior of Ti-6A1-4V blunt V-notched and circular notched samples produced by SLM. The fatigue results were then compared with those of the corresponding smooth samples. The fracture surfaces of the tested samples were evaluated using Environmental Scanning Electron Microscopy (ESEM) and the crack initiation points and fracture mechanisms were identified. (C) 2018 The Authors. Published by Elsevier B.V.

引用

页码：74 / 78

页数：5

共 18 条

[1]

Ayatollahi Majid Reza, 2017, Materials Science Forum, V879, P3, DOI 10.4028/www.scientific.net/MSF.879.3

[2] A numerical study on the effect of symmetric crack flank holes on fatigue life extension of a SENT specimen [J].

Ayatollahi, M. R. ;

Razavi, S. M. J. ;

Chamani, H. R. .

FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES, 2014, 37 (10) :1153-1164

[3] Fatigue strength of severely notched specimens made of Ti-6Al-4V under multiaxial loading [J].

Berto, F. ;

Campagnolo, A. ;

Lazzarin, P. .

FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES, 2015, 38 (05) :503-517

[4] Fatigue in the Aerospace Industry: Striations [J].

Cherolis, Nicholas E. .

JOURNAL OF FAILURE ANALYSIS AND PREVENTION, 2008, 8 (03) :255-258

[5] Improvement of fatigue resistance and ductility of TiAl6V4 processed by selective laser melting [J].

Kasperovich, Galina ;

Hausmann, Joachim .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2015, 220 :202-214

[6] Binding mechanisms in selective laser sintering and selective laser melting [J].

Kruth, JP ;

Mercelis, P ;

Van Vaerenbergh, J ;

Froyen, L ;

Rombouts, M .

RAPID PROTOTYPING JOURNAL, 2005, 11 (01) :26-36

[7]

Leuders S., 2013, INT J FATIGUE, V48, P300

[8] Simulation of additive manufacturing using coupled constitutive and microstructure models [J].

Lindgren, Lars-Erik ;

Lundback, Andreas ;

Fisk, Martin ;

Pederson, Robert ;

Andersson, Joel .

ADDITIVE MANUFACTURING, 2016, 12 :144-158

[9] Fatigue strength of blunt V-notched specimens produced by selective laser melting of Ti-6Al-4V [J].

Razavi, N. ;

Ferro, P. ;

Berto, F. ;

Torgersen, J. .

THEORETICAL AND APPLIED FRACTURE MECHANICS, 2018, 97 :376-384

[10] Fatigue Behavior of Porous Ti-6Al-4V Made by Laser-Engineered Net Shaping [J].

Razavi, Seyed Mohammad Javad ;

Bordonaro, Giancarlo G. ;

Ferro, Paolo ;

Torgersen, Jan ;

Berto, Filippo .

MATERIALS, 2018, 11 (02)

← 1 2 →