Effect of shot peening on the residual stress and microstructure of duplex stainless steel

被引：40

作者：

Feng, Qiang ^{[1
]}

Jiang, Chuanhai ^{[1
]}

Xu, Zhou ^{[1
]}

Xie, Lechun ^{[1
]}

Ji, Vincent ^{[2
]}

机构：

[1] Shanghai Jiao Tong Univ, Sch Mat Sci & Engn, Shanghai 200240, Peoples R China

[2] Univ Paris 11, LEMHE ICMMO, UMR 8182, F-91405 Orsay, France

来源：

SURFACE & COATINGS TECHNOLOGY | 2013年 / 226卷

关键词：

Duplex stainless steel; Shot peening; Residual stress; Microstructure; Rietveld method; TEMPERATURE; FATIGUE; DEFORMATION; BEHAVIOR; STRAIN; DIFFRACTION; MARTENSITE; GROWTH; STATE; SIZE;

D O I：

10.1016/j.surfcoat.2013.03.047

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

The effect of shot peening (SP) treatment on duplex stainless steel S32205 is studied in order to improve the material surface properties. Residual stress distributions in both ferrite and austenite are investigated by X-ray diffraction, and microstructure is explored using Rietveld method. The results reveal that different distributions of compressive residual stress between ferrite and austenite under the same SP condition are resulted from the diverse hardness for different phases in duplex stainless steel. After SP, domain sizes in both ferrite and austenite are refined, and microstrain, dislocation densities and compound fault probabilities are observed to increase sharply in the near surface layer. It is found that distribution trends of residual stresses along the variation of depths are similar to those of lattice parameters for both phases. It can be obtained that in the near-top surface layers, the SP influence on residual stresses and microstructure of austenite is stronger than those of ferrite under the same SP condition. These results reveal that SP treatment with proper processing is efficient for the improvement of the surface properties of duplex stainless S32205. (C) 2013 Elsevier B.V. All rights reserved.

引用

页码：140 / 144

页数：5

共 34 条

[1] Cyclic deformation and near surface microstructures of shot peened or deep rolled austenitic stainless steel AISI 304 [J].

Altenberger, I ;

Scholtes, B ;

Martin, U ;

Oettel, H .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1999, 264 (1-2) :1-16

[2] Growth of short cracks during low and high cycle fatigue in a duplex stainless steel [J].

Alvarez-Armas, I. ;

Krupp, U. ;

Balbi, M. ;

Herenu, S. ;

Marinelli, M. C. ;

Knobbe, H. .

INTERNATIONAL JOURNAL OF FATIGUE, 2012, 41 :95-100

[3] Experimental characterization of short fatigue crack kinetics in an austeno-ferritic duplex steel [J].

Alvarez-Armas, I. ;

Knobbe, H. ;

Marinelli, M. C. ;

Balbi, M. ;

Herenu, S. ;

Krupp, U. .

11TH INTERNATIONAL CONFERENCE ON THE MECHANICAL BEHAVIOR OF MATERIALS (ICM11), 2011, 10 :1491-1496

[4]

[Anonymous], 2011, MAUD VER 2 33

[5]

[Anonymous], RES C P

[6] The influence of temperature on the cyclic behavior of aged and unaged super duplex stainless steels [J].

Armas, A. F. ;

Herenu, S. ;

Alvarez-Armas, I. ;

Degallaix, S. ;

Condo, A. ;

Lovey, F. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2008, 491 (1-2) :434-439

[7] Beneficial effects induced by high temperature cycling in aged duplex stainless steel [J].

Armas, A. F. ;

Degallaix, S. ;

Degallaix, G. ;

Herenu, S. ;

Marinelli, C. ;

Alvarez-Armas, I. .

MECHANICAL BEHAVIOR OF MATERIALS X, PTS 1AND 2, 2007, 345-346 :339-+

[8] The effect of shot peening on fatigue and corrosion behavior of 316L stainless steel in Ringer's solution [J].

Azar, V. ;

Hashemi, B. ;

Yazdi, Mahboobeh Rezaee .

SURFACE & COATINGS TECHNOLOGY, 2010, 204 (21-22) :3546-3551

[9] Review of shot peening processes to obtain nanocrystalline surfaces in metal alloys [J].

Bagherifard, S. ;

Guagliano, M. .

SURFACE ENGINEERING, 2009, 25 (01) :3-14

[10]

BAGHERIFARD S, 2012, SURF COAT TECH, DOI DOI 10.1016/J.SURFC0AT2012.04.002

← 1 2 3 4 →