Effect introduced high density of precipitates on the microstructural evolutions during multi-direction forging of Al-Zn-Mg-Cu alloy

被引：16

作者：

Zhao, Jiuhui ^{[1
]}

Deng, Yunlai ^{[1
,2
,3
]}

Tang, Jianguo ^{[1
,2
]}

Zhang, Jin ^{[1
]}

机构：

[1] Cent South Univ, Light Alloy Res Inst, Changsha, Peoples R China

[2] Cent South Univ, Sch Mat Sci & Engn, Changsha, Peoples R China

[3] Cent South Univ, State Key Lab High Performance & Complex Mfg, Changsha, Peoples R China

来源：

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2020年 / 798卷

关键词：

Multi-directional forging; Al-Zn-Mg-Cu alloys; Recrystallization mechanism; Grain refinement; SEVERE PLASTIC-DEFORMATION; MECHANICAL-PROPERTIES; ALUMINUM-ALLOY; GRAIN-REFINEMENT; TEMPERATURE; STRAIN; 7475-AL-ALLOY; BEHAVIOR; ECAP; SC;

D O I：

10.1016/j.msea.2020.139927

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

Large number density of coarse precipitates were introduced into the Al-Zn-Mg-Cu alloy by interrupted aging and then over-aging at 300 degrees C. Both the overaged and homogenized samples were isothermal MDFed at 5 x 10(-3) s(-1) with temperatures ranging from 300 degrees C to 450 degrees C to investigate the effect of high number density of precipitates on the microstructural evolutions. The results showed that the precipitates decreased gradually during MDF of overaged samples at 300 degrees C and 350 degrees C while they were almost dissolved at 400 degrees C and 450 degrees C. And as the result of that the precipitates could pin dislocations during deformation, and much greater grain refinement was achieved during MDF of overaged samples at 300 degrees C and 350 degrees C.

引用

页数：10

共 50 条

[41] Restirring and Reheating Effects on Microstructural Evolution of Al-Zn-Mg-Cu Alloy during Underwater Friction Stir Additive Manufacturing
Li, Ying
He, Changshu
Wei, Jingxun
Zhang, Zhiqiang
Tian, Ni
Qin, Gaowu
Zhao, Xiang
MATERIALS, 2022, 15 (11)
[42] Effect of Deformation Mode on Grain Characteristics and Strength-Toughness of Al-Zn-Mg-Cu Alloy
Shi, Guohui
Yu, Mingyang
Zhu, Kai
Ren, Weicai
Wen, Kai
Li, Xiwu
MATERIALS, 2024, 17 (18)
[43] Precipitation behavior and precipitates characterization of Al-Zn-Mg-Cu alloy during the non-isothermal aging process
Chen, Zhongwei
Ren, Congcong
Le, Wei
An, Bo
VACUUM, 2025, 233
[44] Effect of strain on cavity development during Al-Zn-Mg-Cu alloy superplastic flow
Li, Guangyu
Ding, Hua
Wang, Jian
Zhang, Wenjing
Zhang, Ning
Hou, Hongliang
MATERIALS SCIENCE AND TECHNOLOGY, 2019, 35 (08) : 939 - 945
[45] Precipitation behaviour in an Al-Zn-Mg-Cu alloy subjected to high strain rate compression tests
Khan, Muhammad Abubaker
Wang, Yangwei
Hamza, Muhammad
Yasin, Ghulam
Tabish, Mohammad
Feng, Chuangshi
Khan, Waheed Qamar
Ahmad, Tahir
Liao, Wei-Bing
Afifi, Mohamed A.
MATERIALS CHARACTERIZATION, 2021, 180
[46] Analysis for Precipitates of Spray Formed Al-Zn-Mg-Cu Alloy after Aging
Hou Xiaohu
Bai Pucun
Zhang Xiuyun
Dong Taishang
Cui Xiaoming
Wang Na
RARE METAL MATERIALS AND ENGINEERING, 2010, 39 : 332 - 335
[47] Effect of multi-directional hot forging process on the microstructure and mechanical properties of Al-Si based alloy containing high amount of Zn and Cu
Alemdag, Yasin
Karabiyik, Sadun
Mikhaylovskaya, Anastasia V.
Kishchik, Mikhail S.
Purcek, Gencaga
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2021, 803
[48] Effect of Zn content on the dynamic softening of Al-Zn-Mg-Cu alloys during hot compression deformation
Tang, Jie
Wang, Jinhai
Teng, Jie
Wang, Guan
Fu, Dingfa
Zhang, Hui
Jiang, Fulin
VACUUM, 2021, 184
[49] Quantitative evaluation of precipitates in an Al-Zn-Mg-Cu alloy after isothermal aging
Du, ZW
Sun, ZM
Shao, BL
Zhou, TT
Chen, CQ
MATERIALS CHARACTERIZATION, 2006, 56 (02) : 121 - 128
[50] Phase formation and microstructural evolution during sintering of Al-Zn-Mg-Cu alloys
Mohammadi, M. Shah
Simchi, A.
Gierl, C.
POWDER METALLURGY, 2010, 53 (01) : 62 - 70

← 1 2 3 4 5 →