High-Tech Hip Implant for Wireless Temperature Measurements In Vivo

被引:40
作者
Bergmann, Georg [1 ]
Graichen, Friedmar [1 ]
Dymke, Joern [1 ]
Rohlmann, Antonius [1 ]
Duda, Georg N. [1 ]
Damm, Philipp [1 ]
机构
[1] Charite, Julius Wolff Inst, D-13353 Berlin, Germany
关键词
TELEMETRY SYSTEM; ORTHOPEDIC IMPLANTS; JOINT SIMULATOR; SYNOVIAL-FLUIDS; WEAR; PROSTHESES; REPLACEMENTS; FORCES; LOADS; BONE;
D O I
10.1371/journal.pone.0043489
中图分类号
O [数理科学和化学]; P [天文学、地球科学]; Q [生物科学]; N [自然科学总论];
学科分类号
07 ; 0710 ; 09 ;
摘要
When walking long distances, hip prostheses heat up due to friction. The influence of articulating materials and lubricating properties of synovia on the final temperatures, as well as any potential biological consequences, are unknown. Such knowledge is essential for optimizing implant materials, identifying patients who are possibly at risk of implant loosening, and proving the concepts of current joint simulators. An instrumented hip implant with telemetric data transfer was developed to measure the implant temperatures in vivo. A clinical study with 100 patients is planned to measure the implant temperatures for different combinations of head and cup materials during walking. This study will answer the question of whether patients with synovia with poor lubricating properties may be at risk for thermally induced bone necrosis and subsequent implant failure. The study will also deliver the different friction properties of various implant materials and prove the significance of wear simulator tests. A clinically successful titanium hip endoprosthesis was modified to house the electronics inside its hollow neck. The electronics are powered by an external induction coil fixed around the joint. A temperature sensor inside the implant triggers a timer circuit, which produces an inductive pulse train with temperature-dependent intervals. This signal is detected by a giant magnetoresistive sensor fixed near the external energy coil. The implant temperature is measured with an accuracy of 0.1 degrees C in a range between 20 degrees C and 58 degrees C and at a sampling rate of 2-10 Hz. This rate could be considerably increased for measuring other data, such as implant strain or vibration. The employed technique of transmitting data from inside of a closed titanium implant by low frequency magnetic pulses eliminates the need to use an electrical feedthrough and an antenna outside of the implant. It enables the design of mechanically safe and simple instrumented implants.
引用
收藏
页数:7
相关论文
共 39 条
[1]  
[Anonymous], 1995, ISO72068
[2]  
[Anonymous], 1992, ISO72066
[3]   Frictional heating of total hip implants. Part 1. measurements in patients [J].
Bergmann, G ;
Graichen, F ;
Rohlmann, A ;
Verdonschot, N ;
van Lenthe, GH .
JOURNAL OF BIOMECHANICS, 2001, 34 (04) :421-428
[4]   Frictional heating of total hip implants. Part 2: finite element study [J].
Bergmann, G ;
Graichen, F ;
Rohlmann, A ;
Verdonschot, N ;
van Lenthe, GH .
JOURNAL OF BIOMECHANICS, 2001, 34 (04) :429-435
[5]   MULTICHANNEL STRAIN-GAUGE TELEMETRY FOR ORTHOPEDIC IMPLANTS [J].
BERGMANN, G ;
GRAICHEN, F ;
SIRAKY, J ;
JENDRZYNSKI, H ;
ROHLMANN, A .
JOURNAL OF BIOMECHANICS, 1988, 21 (02) :169-176
[6]   Friction of total hip replacements with different bearings and loading conditions [J].
Brockett, Claire ;
Williams, Sophie ;
Jin, Zhongmin ;
Isaac, Graham ;
Fisher, John .
JOURNAL OF BIOMEDICAL MATERIALS RESEARCH PART B-APPLIED BIOMATERIALS, 2007, 81B (02) :508-515
[7]   TELEMETERING INVIVO LOADS FROM NAIL PLATE IMPLANTS [J].
BROWN, RH ;
BURSTEIN, AH ;
FRANKEL, VH .
JOURNAL OF BIOMECHANICS, 1982, 15 (11) :815-&
[8]  
Chikama H, 1985, Nihon Seikeigeka Gakkai Zasshi, V59, P559
[9]   Comparison of two methods for calculating the frictional properties of articular cartilage using a simple pendulum and intact mouse knee joints [J].
Drewniak, Elizabeth I. ;
Jay, Gregory D. ;
Fleming, Braden C. ;
Crisco, Joseph J. .
JOURNAL OF BIOMECHANICS, 2009, 42 (12) :1996-1999
[10]  
Fam H, 2007, BIORHEOLOGY, V44, P59