Innovative Comparison on the Performance of TiCN Coated Drill Bit and Uncoated Drill Bit in the Novel CNC Drilling of LDX 2205 Duplex Stainless Steel for Minimizing Tool Wear

被引：0

作者：

Chekuri, Venkatasaikumar ^{[1
]}

Thiagarajan, C. ^{[1
]}

机构：

[1] Saveetha Univ, Saveetha Inst Med & Tech Sci, Saveetha Sch Engn, Dept Automobile Engn, Chennai 602105, Tamil Nadu, India

来源：

JOURNAL OF PHARMACEUTICAL NEGATIVE RESULTS | 2022年 / 13卷

关键词：

LDX 2205 duplex stainless steel; Tool Wear; Novel CNC drilling; Novel machining; TiCN drill bit; HSS drill bit; PARAMETERS;

D O I：

10.47750/pnr.2022.13.S04.056

中图分类号：

R9 [药学];

学科分类号：

1007 ;

摘要：

Aim: This research focuses on minimizing the Tool Wear (TW) by comparing the performance of conventional uncoated HSS drill bit with TiCN drill bit for the machining of LDX 2205 duplex stainless steel in novel CNC drilling machine. Materials and Methods: The materials used for drill bits were Titanium Carbonitride (TiCN) coated HSS drill bit and uncoated HSS drill bit. LDX 2205 Duplex Stainless Steel was used as workpiece. A total of 40 specimens were divided into 2 groups with 80% G-Power calculator, to measure the TW of two drill bits in novel CNC drilling machine. Cutting force, drill depth, spindle speed, tool geometry, rate of feed were the controlled factors. Results: Observed results for each drill bit were recorded and analyzed using SPSS Software. Final experimental values of TW were investigated and obtained, having mean TW value of 0.9324 mm for the HSS drill bit and mean TW value of 0.7502 mm for TiCN drill bit. These values were obtained with a significance level of 0.030 which is less than 0.05 (p<0.05). Conclusion: Within the limits of this study, TiCN drill bit has lower tool wear when compared to the HSS drill bit in the novel CNC drilling of LDX 2205 duplex stainless steel.

引用

页码：507 / 516

页数：10

共 30 条

[11]

Fischer Alfons, 2011, FRICTION WEAR WEAR P

[12]

Goyal Tarun, 2017, NEAR DRY MACHINING S

[13] Experimental studies on Drilling of 410 Stainless Steel [J].

Jayaganth, A. ;

Jayakumar, K. ;

Deepak, A. ;

Pazhanivel, K. .

MATERIALS TODAY-PROCEEDINGS, 2018, 5 (02) :7168-7173

[14] A comprehensive study on the effects of multiple injection strategies and exhaust gas recirculation on diesel engine characteristics that utilize waste high density polyethylene oil [J].

Jayanth, Bellappu Venkat ;

Depoures, Melvin Victor ;

Kaliyaperumal, Gopal ;

Dillikannan, Damodharan ;

Jawahar, Dilipsingh ;

Palani, Kumaran ;

Shivappa, Ganesha Prasad Meravanigee .

ENERGY SOURCES PART A-RECOVERY UTILIZATION AND ENVIRONMENTAL EFFECTS, 2021, :7749-7766

[15] Melatonin delivery from PCL scaffold enhances glycosaminoglycans deposition in human chondrocytes - Bioactive scaffold model for cartilage regeneration [J].

Kamath, Manjunath S. ;

Rao, Subha Krishna ;

Jaison, D. ;

Sridhar, K. ;

Kasthuri, N. ;

Gopinath, V ;

Sivaperumal, P. ;

Patil, Shantanu S. .

PROCESS BIOCHEMISTRY, 2020, 99 (99) :36-47

[16]

Kumar J., 2018, EFFECT DRILLING PARA

[17]

Maruda RW., 2018, ARCH MECH TECHNOLOGY, V38, P45, DOI [10.2478/amtm-2018-0008, DOI 10.2478/AMTM-2018-0008]

[18] Machinability study of first generation duplex (2205), second generation duplex (2507) and austenite stainless steel during drilling process [J].

Nomani, J. ;

Pramanik, A. ;

Hilditch, T. ;

Littlefair, G. .

WEAR, 2013, 304 (1-2) :20-28

[19] Mechanical, thermal and fatigue behaviour of surface-treated novelCaryota urensfibre-reinforced epoxy composite [J].

Prakash, V. R. Arun ;

Xavier, J. Francis ;

Ramesh, G. ;

Maridurai, T. ;

Kumar, K. Siva ;

Raj, R. Blessing Sam .

BIOMASS CONVERSION AND BIOREFINERY, 2022, 12 (12) :5451-5461

[20] Collective influence of 1-decanol addition, injection pressure and EGR on diesel engine characteristics fueled with diesel/LDPE oil blends [J].

Rajasekaran, S. ;

Damodharan, D. ;

Gopal, K. ;

Kumar, B. Rajesh ;

De Poures, Melvin Victor .

FUEL, 2020, 277

← 1 2 3 →