Evaluating the effect of protein composition on gelation and viscoelastic characteristics of acid-induced whey protein gels

被引:24
作者
de Faria, Janaina Teles [1 ]
Rodrigues Minim, Valeria Paula [1 ]
Minim, Luis Antonio [1 ]
机构
[1] Univ Fed Vicosa, Dept Food Technol, Vicosa, MG, Brazil
关键词
Cold gelation; Whey protein; Creep-recovery; Stress relaxation; Oscillatory measurement; Glucono-delta-lactone; HEAT-INDUCED GELATION; BOVINE SERUM-ALBUMIN; COLD-SET GELS; RHEOLOGICAL PROPERTIES; GLOBULAR-PROTEINS; MILK; MICROSTRUCTURE; AGGREGATION; BEHAVIOR;
D O I
10.1016/j.foodhyd.2012.12.006
中图分类号
O69 [应用化学];
学科分类号
081704 ;
摘要
The effects of protein composition on the gelation and rheological characteristics of acid-induced whey protein gels were studied. Gels composed of mixtures containing beta-Lactoglobulin (beta-Lg), alpha-Lactalbumin (alpha-La) and glycomacropeptide (GMP) were rheologically investigated using a mixture design and analyzed by response surface methodology. All mixtures evaluated gelled and self-supported gels were obtained, except for the gel containing the highest GMP concentration. Gelation was monitored by oscillatory time sweep and the viscoelastic properties were determined by creep-recovery and stress relaxation measurements with the simplified Burgers model and the Peleg equation fitted to the data, respectively. The results showed that a higher elastic modulus was found in gels containing greater proportions of beta-Lg. Addition of alpha-La and/or GMP reduced the elastic character the gels. The gelling time increased as the proportion of alpha-La of the mixture was increased, and as a consequence the pH of gelation was reduced. On the other hand, the effect of GMP addition presented the opposite effect. Considering the creep-recovery test, there was a decrease in the simplified Burgers model parameters with the increased proportion of alpha-La and/or GMP in the mixture. For all gels, the main deformation was caused by the retarded elastic strain, and the reversible deformation was higher than the irreversible deformation. It was also observed that the stress relaxation process was more pronounced in mixtures with lower proportion of beta-Lg. Mixed gels were structurally more fragile, and beta-Lg was the main component responsible for strengthening the network. (c) 2012 Elsevier Ltd. All rights reserved.
引用
收藏
页码:64 / 71
页数:8
相关论文
共 42 条
[1]  
Alting A. C., 2003, J AGR FOOD CHEM, V51, P3150
[2]   Physical and chemical interactions in cold gelation of food proteins [J].
Alting, AC ;
de Jongh, HHJ ;
Visschers, RW ;
Simons, JWFA .
JOURNAL OF AGRICULTURAL AND FOOD CHEMISTRY, 2002, 50 (16) :4682-4689
[3]   Acid-induced cold gelation of globular proteins: Effects of protein aggregate characteristics and disulfide bonding on rheological properties [J].
Alting, AC ;
Weijers, M ;
De Hoog, EHA ;
van de Pijpekamp, AM ;
Stuart, MAC ;
Hamer, RJ ;
De Kruif, CG ;
Visschers, RW .
JOURNAL OF AGRICULTURAL AND FOOD CHEMISTRY, 2004, 52 (03) :623-631
[4]   Number of thiol groups rather than the size of the aggregates determines the hardness of cold set whey protein gels [J].
Alting, AC ;
Hamer, RJ ;
de Kruif, CG ;
Paques, M ;
Visschers, RW .
FOOD HYDROCOLLOIDS, 2003, 17 (04) :469-479
[5]  
[Anonymous], 1999, DAIRY TECHNOLOGY PRI
[6]   CA2+-INDUCED GELATION OF PRE-HEATED WHEY-PROTEIN ISOLATE [J].
BARBUT, S ;
FOEGEDING, EA .
JOURNAL OF FOOD SCIENCE, 1993, 58 (04) :867-871
[7]   Influence of xanthan gum on physical characteristics of heat-denatured whey protein solutions and gels [J].
Bryant, CM ;
McClements, DJ .
FOOD HYDROCOLLOIDS, 2000, 14 (04) :383-390
[8]   Molecular basis of protein functionality with special consideration of cold-set gels derived from heat-denatured whey [J].
Bryant, CM ;
Mcclements, DJ .
TRENDS IN FOOD SCIENCE & TECHNOLOGY, 1998, 9 (04) :143-151
[9]   Rheological characteristics and texture attributes of glutinous rice cakes (mochi) [J].
Chuang, GCC ;
Yeh, AI .
JOURNAL OF FOOD ENGINEERING, 2006, 74 (03) :314-323
[10]  
Clark AH, 2009, MODERN BIOPOLYMER SCIENCE: BRIDGING THE DIVIDE BETWEEN FUNDAMENTAL TREATISE AND INDUSTRIAL APPLICATION, P1, DOI 10.1016/B978-0-12-374195-0.00001-X