Determination of optimum rock cutting data through single pick cutting tests

被引:8
|
作者
Yasar, S. [1 ]
机构
[1] Karadeniz Tech Univ, Min Engn Dept, Trabzon, Turkey
关键词
excavation; rocks/rock mechanics; tunnels & tunnelling; PERFORMANCE; PREDICTION; FORCES;
D O I
10.1680/jgele.18.00124
中图分类号
P5 [地质学];
学科分类号
0709 ; 081803 ;
摘要
Partial-face rock excavation machines, which are equipped with conical picks form a major share in the mineral production and in the roadway excavation for underground mines. Consequently, the performance of these machines plays a key role for the success of the project where the prediction of its performance generally relies on the instrumented cutting tests requiring a large rock sample. These rock samples, however, are in most cases impossible to be collected from excavation sites, especially from underground mines due to safety issues and harsh working environment. Therefore, alternative reliable methods requiring a smaller amount of rock sample are preferred. This paper was tailored to address a new plot to convert the index cutting data from the core cutting test into the optimum rock cutting data where these data are used for performance prediction and machine design. A special emphasis was given to medium strength rocks in which partial-face rock excavation machines frequently operate. Nine rock samples were collected from quarries and roadheader excavation sites, which have a strength spectrum from 1.89 to 99.92 MPa and these samples were subjected to rock cutting tests both using the procedure for the core-cutting test in single pick cutting mode and for the conical pick cutting test in relieved mode. In virtue of cutting tests, predictive plots were developed to determine the optimum conical pick cutting data through conducting a single pick cutting test using a small block sample. The major conclusion drawn from the experimental results is in the absence of large rock sample for an instrumented cutting test, small block or core samples can be utilised for estimation of optimum rock cutting data, especially for very low and medium strength rocks.
引用
收藏
页码:8 / 14
页数:7
相关论文
共 50 条
  • [31] Effects of cut depth and cut spacing on a conical pick in rock cutting
    Liao Jiu-bo
    Li Xi-bing
    Wang Shao-feng
    Du Kun
    ROCK AND SOIL MECHANICS, 2023, 44 (04) : 1009 - 1021
  • [32] Applicability of Texture Coefficient Concept for the Prediction of Pick Performance in Rock Cutting
    Tiryaki, Bülent
    Dikmen, A. Çagatay
    Kadioglu, Yusuf K.
    Özbilgin, Deniz
    Tiryaki, Nazife
    Bölükbas¸i, Naci
    Madencilik, 2003, 42 (02): : 27 - 43
  • [33] Load Characteristics of Pick Cutting Coal Seams with Coal and Rock Interface
    Luo, Chenxu
    Jing, Shuangxi
    Han, Xiaoming
    Liu, Yu
    Du, Changlong
    JORDAN JOURNAL OF MECHANICAL AND INDUSTRIAL ENGINEERING, 2016, 10 (03): : 205 - 210
  • [34] Research on Cutting Performance of Conical Pick Cutting Rock Plate with One Side Constrain and Three Sides Free
    Lu, Zhenguo
    Wang, Hongbin
    Zeng, Qingliang
    Wang, Zhiwen
    Wan, Lirong
    Li, Changjiang
    SCIENCE PROGRESS, 2022, 105 (01)
  • [35] Fold catastrophe analysis of constitutive model of pick cutting coal with rock
    Luo, Chenxu
    Qiao, Junbei
    Zhou, Jiawei
    Sun, Zhijia
    Cao, Jun
    ENERGY REPORTS, 2022, 8 : 9 - 15
  • [36] An Analytical Model for Rock Cutting with a Chisel Pick of the Cutter Suction Dredger
    Ouyang, Yiping
    Yang, Qi
    Chen, Xinquan
    Xu, Yongfu
    JOURNAL OF MARINE SCIENCE AND ENGINEERING, 2020, 8 (10) : 1 - 23
  • [37] Development of a portable rock cutting rig for rock cuttability determination
    Bilgin, N.
    Balci, C.
    Tumac, D.
    Feridunoglu, C.
    Copur, H.
    ROCK MECHANICS IN CIVIL AND ENVIRONMENTAL ENGINEERING, 2010, : 405 - 408
  • [38] Evaluation of saturation effects on drag pick cutting of a brittle sandstone from full scale linear cutting tests
    Abu Bakar, Muhammad Zubair
    Gertsch, Leslie Sour
    TUNNELLING AND UNDERGROUND SPACE TECHNOLOGY, 2013, 34 : 124 - 134
  • [39] Drag pick cutting tests: A comparison between experimental and theoretical results
    Yasar, Serdar
    Yilmaz, Ali Osman
    JOURNAL OF ROCK MECHANICS AND GEOTECHNICAL ENGINEERING, 2018, 10 (05) : 893 - 906
  • [40] Drag pick cutting tests: A comparison between experimental and theoretical results
    Serdar Yasar
    Ali Osman Yilmaz
    Journal of Rock Mechanics and Geotechnical Engineering, 2018, (05) : 893 - 906