Mechanical properties of a novel fiber metal laminate based on a carbon fiber reinforced Zn-Al alloy composite

被引：37
作者：
Hao, Xinwei [1 ,2 ]
Nie, Huihui [1 ,2 ]
Ye, Zhe [1 ,2 ]
Luo, Yi [1 ,2 ]
Zheng, Liuwei [1 ,2 ]
Liang, Wei [1 ,2 ]
机构：
[1] Shanxi Key Lab Adv Magnesium Based Mat, Taiyuan 030024, Shanxi, Peoples R China
[2] Taiyuan Univ Technol, Coll Mat Sci & Engn, Taiyuan 030024, Shanxi, Peoples R China
来源：
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2019年 / 740卷
基金：
中国国家自然科学基金;
关键词：
Fiber metal laminates (FMLs); Diffusion bonding; Carbon fiber reinforced Metal Matrix; Composites (CfMMCs); Zn-Al alloy; Interface; TENSILE PROPERTIES; CAST ALLOYS; MICROSTRUCTURE; JOINTS; EVOLUTION; NANOSTRUCTURES; MAGNESIUM; BEHAVIOR; CFRP;
D O I：
10.1016/j.msea.2018.10.050
中图分类号：
TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
Fiber metal laminates (FMLs) which consist of magnesium alloy layers and a continuous carbon fiber-reinforced Zn-Al alloy composites layer (the mass fraction of Al is 8%) were fabricated by the diffusion bonding method. The Zn-Al alloy used as the solder of the FMLs in this paper infiltrated the carbon fiber well and bonded the carbon fiber and magnesium alloy layer tightly. Tensile results indicated an improvement of the tensile strength and elastic modulus by 103% and 41%, respectively, compared with those of the original magnesium alloy sheets. The microstructure of the interfaces between the carbon fiber and Zn-Al, as well as the interface between Mg and Zn-Al, were characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). MgZn2 was formed at the Mg/Zn-Al interface. The component of the C-f/Zn-Al interface was nanoscale Al2O3. This research proves the feasibility of joining metal sheets with carbon fiber-reinforced low-melting-point alloy composite sheets to fabricate metallurgically-bonded FMLs.
引用
收藏
页码：218 / 225
页数：8
相关论文
共 41 条
  • [1] Laminate squeeze casting of carbon fiber reinforced aluminum matrix composites
    Alhashmy, Hasan Ali
    Nganbe, Michel
    [J]. MATERIALS & DESIGN, 2015, 67 : 154 - 158
  • [2] Loading and fracture response of CFRP-to-steel adhesively bonded joints with thick adherents - Part II: Numerical simulation
    Anyfantis, Konstantinos N.
    Tsouvalis, Nicholas G.
    [J]. COMPOSITE STRUCTURES, 2013, 96 : 858 - 868
  • [3] Fiber metal laminates: An advanced material for future aircraft
    Asundi, A
    Choi, AYN
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 1997, 63 (1-3) : 384 - 394
  • [4] Botelho Edson Cocchieri, 2006, Mat. Res., V9, P247
  • [5] Microstructure and tensile properties of 2014 Al alloy reinforced with continuous carbon fibers manufactured by gas pressure infiltration
    Daoud, A
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2005, 391 (1-2): : 114 - 120
  • [6] Strength of epoxy adhesive-bonded stainless-steel joints
    de Morais, A. B.
    Pereira, A. B.
    Teixeira, J. P.
    Cavaleiro, N. C.
    [J]. INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES, 2007, 27 (08) : 679 - 686
  • [7] Aluminium carbide formation in interpenetrating graphite/aluminium composites
    Etter, T.
    Schulz, P.
    Weber, M.
    Metz, J.
    Wimmler, M.
    Loeffler, J. F.
    Uggowitzer, P. J.
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2007, 448 (1-2): : 1 - 6
  • [8] Low velocity impact response of basalt-aluminium fibre metal laminates
    Ferrante, L.
    Sarasini, F.
    Tirillo, J.
    Lampani, L.
    Valente, T.
    Gaudenzi, P.
    [J]. MATERIALS & DESIGN, 2016, 98 : 98 - 107
  • [9] Characterization of ZnAl cast alloys with Li addition
    Gancarz, Tomasz
    Cempura, Grzegorz
    [J]. MATERIALS & DESIGN, 2016, 104 : 51 - 59
  • [10] Characterization of ZnAl cast alloys with Na addition
    Gancarz, Tomasz
    Cempura, Grzegorz
    Skuza, Wojciech
    [J]. MATERIALS CHARACTERIZATION, 2016, 111 : 147 - 153
12345