Induced drilling strains in glass fibre reinforced epoxy composites

被引：16
|
作者：
Nobre, J. P. [1 ,2 ]
Stiffel, J. -H. [2 ]
Nau, A. [3 ]
Outeiro, J. C.
Batista, A. C. [1 ]
Van Paepegem, W. [4 ]
Scholtes, B. [3 ]
机构：
[1] Univ Coimbra, Dept Phys, CEMDRX, P-3030728 Coimbra, Portugal
[2] Univ Coimbra, Dept Mech Engn, P-3030728 Coimbra, Portugal
[3] Univ Kassel, Inst Mat Engn, IfW, D-34109 Kassel, Germany
[4] Univ Ghent, Dept Mat Sci & Engn, B-9052 Ghent, Belgium
来源：
CIRP ANNALS-MANUFACTURING TECHNOLOGY | 2013年 / 62卷 / 01期
关键词：
Drilling; Composite; Residual stress; RESIDUAL-STRESS; ORTHOTROPIC MATERIALS;
D O I：
10.1016/j.cirp.2013.03.089
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Residual strains induced by drilling of glass-fibre reinforced polymers (GFRPs) were determined using a hybrid experimental-numerical methodology. Experimentally, a set of GFRP specimens were drilled under well-defined tensile (calibration) stresses, using an especially designed tensile test device. To remove the effect of the initial residual stresses, this methodology considers differential stress values instead of absolute ones. Numerically, the experimental procedure was simulated using the finite element method. The induced drilling strains were determined by comparing the experimental measured strains with those calculated numerically. Clear differences between the selected drilling operations could be observed and evaluated. (C) 2013 CIRP.
引用
收藏
页码：87 / 90
页数：4
相关论文
共 50 条
  • [1] Influence of cooling on the performance of the drilling process of glass fibre reinforced epoxy composites
    Ramesh, B.
    Elayaperumal, A.
    Satishkumar, S.
    Kumar, Anish
    Jayakumar, T.
    Dinakaran, D.
    ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING, 2016, 16 (03) : 565 - 575
  • [2] Influence of cooling on the performance of the drilling process of glass fibre reinforced epoxy composites
    Ramesh, B.
    Elayaperumal, A.
    Satishkumar, S.
    Kumar, Anish
    Jayakumar, T.
    Dinakaran, D.
    ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING, 2016, 16 (01) : 135 - 146
  • [3] Erosion of Glass Fibre reinforced Epoxy Composites
    Atia, A. M.
    Ali, W. Y.
    KGK-KAUTSCHUK GUMMI KUNSTSTOFFE, 2018, 71 (04): : 22 - 27
  • [4] An investigation into the drilling of carbon and glass fibre reinforced polymer composites
    Charlton, Peter
    Curnick, Paul
    Donne, Kelvin
    Thomas, Richard
    8TH INTERNATIONAL CONFERENCE ON CONDITION MONITORING AND MACHINERY FAILURE PREVENTION TECHNOLOGIES 2011, VOLS 1 AND 2, 2011, : 1333 - 1345
  • [5] Drilling analysis of woven glass fiber-reinforced/epoxy composites
    Khashaba, U. A.
    El-Sonbaty, I. A.
    Selmy, A. I.
    Megahed, A. A.
    JOURNAL OF COMPOSITE MATERIALS, 2013, 47 (02) : 191 - 205
  • [6] Tribological behaviour of glass fibre bundles reinforced epoxy gradient composites
    Dwivedi, U. K.
    Dixit, A.
    Chand, N.
    TRIBOLOGY-MATERIALS SURFACES & INTERFACES, 2009, 3 (03) : 118 - 124
  • [7] Fatigue behaviour of glass fibre reinforced epoxy composites enhanced with nanoparticles
    Borrego, L. P.
    Costa, J. D. M.
    Ferreira, J. A. M.
    Silva, H.
    COMPOSITES PART B-ENGINEERING, 2014, 62 : 65 - 72
  • [8] Drilling of Glass Fibre Reinforced Plastic
    Janos, Liska
    Janos, Kodacsy
    ADVANCED MANUFACTURING TECHNOLOGY, PTS 1-4, 2012, 472-475 : 958 - 961
  • [9] Drilling analysis of thin woven glass-fiber reinforced epoxy composites
    Khashaba, U. A.
    El-Keran, A. A.
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2017, 249 : 415 - 425
  • [10] The influence of hardener-to-epoxy ratio on the interfacial strength in glass fibre reinforced epoxy composites
    Minty, Ross F.
    Yang, Liu
    Thomason, James L.
    COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING, 2018, 112 : 64 - 70
12345