Microstructural Characterization and Mechanical Properties of Powder Metallurgy Dual Phase Steel Preforms

被引：15

作者：

Mahesh, K. ^{[1
]}

Sankaran, S. ^{[1
]}

Venugopal, P. ^{[1
]}

机构：

[1] IIT Madras, Dept Met & Mat Engn, Chennai, Tamil Nadu, India

来源：

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY | 2012年 / 28卷 / 12期

关键词：

Powder metallurgy; Dual phase; Jaoul-Crussard analysis; Work hardening rate; RETAINED AUSTENITE; TENSILE PROPERTIES; COOLING RATE; BEHAVIOR; CARBON; IRON; DEFORMATION; DENSITY;

D O I：

10.1016/S1005-0302(12)60177-7

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

In order to improve the mechanical properties of powder metallurgy (P/M) ferrite-pearlite steel, a dual phase (DP) ferrite-martensite steel was produced through intercritical annealing of sintered P/M preforms. Microstructures of the sintered and DP steels were examined with optical, scanning and transmission electron microscopes. Mechanical properties were evaluated through hardness measurements and compression tests. Microstructural studies revealed that sintered steel contained polygonal ferrite-pearlite while the DP steel contained polygonal, lath and acicular ferrite along with lath-type martensite as microstructural constituents. In DP steels, with increasing mean preform density, the microstructure contained fine and continuous network of martensite colonies with minimum porosity. The work hardening rate vs plastic strain plots (Jaoul-Crussard analysis) of both the steels revealed typical three stage deformation behaviour for low and high mean preform densities. Compression tests revealed that, DP P/M steel displayed higher strength-plasticity combination than the sintered steel.

引用

页码：1085 / 1094

页数：10

共 23 条

[1] Effect of controlled rolling and cooling on the microstructure and mechanical properties of 60Si2MnA spring steel rod [J].

Ai, JH ;

Zhao, TC ;

Gao, HJ ;

Hu, YH ;

Xie, XS .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2005, 160 (03) :390-395

[2] Effects of microstructure and notches on the mechanical properties of dual-phase steels [J].

Bayram, A ;

Uguz, A ;

Ula, M .

MATERIALS CHARACTERIZATION, 1999, 43 (04) :259-269

[3] TENSILE PROPERTIES AND INHOMOGENEOUS DEFORMATION OF FERRITE MARTENSITE DUAL-PHASE STEELS [J].

BYUN, TS ;

KIM, IS .

JOURNAL OF MATERIALS SCIENCE, 1993, 28 (11) :2923-2932

[4] INFLUENCE OF POWDERS ON FINAL PROPERTIES AND MICROSTRUCTURE OF SINTERED MOLYBDENUM STEELS [J].

CAMBRONERO, LEG ;

FERNANDEZ, C ;

TORRALBA, JM ;

RUIZPRIETO, JM .

POWDER METALLURGY, 1994, 37 (01) :53-56

[5] Simulation of the controlled rolling and accelerated cooling of a bainitic steel using torsion testing [J].

Cota, AB ;

Barbosa, R ;

Santos, DB .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2000, 100 (1-3) :156-162

[6]

Cribb W.R., 1979, STRUCTURE PROPERTIES, P91

[7]

DeHoff R., 1968, QUANTITATIVE MICROSC

[8] EFFECT OF CARBON ON MICROSTRUCTURE OF MIXED POWDER SYSTEM COOLED AT MODERATE RATES AFTER SINTERING [J].

FODOR, M ;

WOOD, JV .

POWDER METALLURGY, 1995, 38 (02) :141-146

[9] Tensile properties of iron-based P/M steels with ferrite plus martensite microstructure [J].

Gural, A. ;

Tekeli, S. ;

Ando, T. .

JOURNAL OF MATERIALS SCIENCE, 2006, 41 (23) :7894-7901

[10] OBSERVATION OF DEFORMATION AND TRANSFORMATION BEHAVIOR OF RETAINED AUSTENITE IN A 0.14C-1.2SI-1.5MN STEEL WITH FERRITE BAINITE AUSTENITE STRUCTURE [J].

JEONG, WC ;

MATLOCK, DK ;

KRAUSS, G .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1993, 165 (01) :1-8

← 1 2 3 →