High pressure gas quenching: Distortion analysis in gears after heat treatment

被引：16

作者：

Atraszkiewicz, R. ^{[1
]}

Januszewicz, B. ^{[1
]}

Kaczmarek, L. ^{[1
]}

Stachurski, W. ^{[2
]}

Dybowski, K. ^{[1
]}

Rzepkowski, A. ^{[1
]}

机构：

[1] Tech Univ Lodz, Inst Mat Sci & Engn, PL-90924 Lodz, Poland

[2] Tech Univ Lodz, Inst Machine Tools & Prod Engn, PL-90924 Lodz, Poland

来源：

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2012年 / 558卷

关键词：

Martensite; Hardening; Distortion; Hardness measurement; Thermomechanical processing; STEEL;

D O I：

10.1016/j.msea.2012.08.047

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

The analysis of distortions, hardness level and microstructure of the surface layers of the toothed gears after low pressure carburizing and high pressure gas quenching is presented in this paper. Toothed gears of module 2 made of 16MnCr5 steel, case carburized to depth 0.3 mm and toothed gears of module 5 made of 15CrNi6 steel, case carburized to depth 0.6 mm were analyzed. Quenching intensity of nitrogen and helium was compared and its influence on microstructure, dimensional changes and wheels geometry was assessed. Helium is proposed as an alternative cooling medium because of its higher quenching power in comparison to nitrogen. Better mechanical properties of the core of case hardened elements were achieved in case of helium quenching. No negative effect of helium cooling medium on surface layer microstructures and level of distortions was observed. (C) 2012 Elsevier B.V. All rights reserved.

引用

页码：550 / 557

页数：8

共 20 条

[1]

Altena H., 2004, IND HEAT, V71, P145

[2]

Altena H., 2010, MONATSH, V155, P417

[3]

Bergstrom C.M., 1988, HARTEREI TECHNISCHE, V43, P36

[4] Distortion minimization of disks for gear manufacture [J].

Brinksmeier, Ekkard ;

Luebben, Thomas ;

Fritsching, Udo ;

Cui, Chengsong ;

Rentsch, Ruediger ;

Soelter, Jens .

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2011, 51 (04) :331-338

[5] Distortions induced by heat treatment of automotive bevel gears [J].

Cho, JR ;

Kang, WJ ;

Kim, MG ;

Lee, JH ;

Lee, YS ;

Bae, WB .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2004, 153 :476-481

[6] Performance of containers with hydrogen storage alloys for hydrogen compression in heat treatment facilities [J].

Cieslik, J. ;

Kula, P. ;

Sato, R. .

JOURNAL OF ALLOYS AND COMPOUNDS, 2011, 509 (09) :3972-3977

[7] Research on compressor utilizing hydrogen storage materials for application in heat treatment facilities [J].

Cieslik, J. ;

Kula, P. ;

Filipek, S. M. .

JOURNAL OF ALLOYS AND COMPOUNDS, 2009, 480 (02) :612-616

[8]

Cristinacce M, 1999, HEAT TREAT MET, V26, P18

[9]

Dawes C., 1971, METAL PROGR, P72

[10]

Fradkin E.I., 2009, VESTN MASHINOSTR, V10, P43

← 1 2 →