Effects of high temperature plasma immersion ion implantation on wear resistance of Ti-Si-B sintered alloys

被引：7

作者：

Fernandes, Bruno Bacci ^{[1
]}

Oliveira, Rogerio Moraes ^{[1
]}

Ueda, Mario ^{[1
]}

Magalhaes Mariano, Samantha de Fatima ^{[1
,2
]}

Ramos, Alfeu Saraiva ^{[3
]}

Vieira, Maxson Souza ^{[1
]}

Lourenco de Melo, Francisco Cristovao ^{[4
]}

de Oliveira, Guilherme ^{[1
,2
]}

机构：

[1] INPE, LAP, Sao Jose Dos Campos, SP, Brazil

[2] ETEP Fac, BR-12600970 Sao Jose Dos Campos, SP, Brazil

[3] Univ Estadual Paulista, UNESP, FEG, BR-12516410 Guaratingueta, SP, Brazil

[4] IAE, DCTA, BR-12228904 Sao Jose Dos Campos, SP, Brazil

来源：

SURFACE & COATINGS TECHNOLOGY | 2013年 / 228卷

基金：

巴西圣保罗研究基金会;

关键词：

Titanium alloys; Tribological properties; Powder metallurgy; TITANIUM-ALLOYS; POWDER-METALLURGY; N COATINGS; MICROSTRUCTURE; TI-6AL-4V; MARINE;

D O I：

10.1016/j.surfcoat.2013.04.029

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

Although titanium and its alloys own good mechanical properties and excellent corrosion resistance, these materials present poor tribological properties for specific applications that require wear resistance. In order to produce wear-resistant surfaces, this work is aimed at achieving improvement of wear characteristics in Ti-Si-B alloys by means of high temperature nitrogen plasma immersion ion implantation (Pill). These alloys were produced by powder metallurgy using high energy ball milling and hot pressing. Scanning electron microscopy (SEM) and X-ray diffraction identified the presence of alpha-titanium, Ti6Si2B, Ti5Si3, TiB and Ti3Si phases. Wear tests were carried out with a ball-on-disk tribometer to evaluate the friction coefficient and wear rate in treated and untreated samples. The worn profiles were measured by visible light microscopy and examined by SEM in order to determine the wear rates and wear mechanisms. Ti-7.5Si-22.5B alloy presented the highest wear resistance amongst the untreated alloys produced in this work. High temperature PIII was effective to reduce the wear rate and friction coefficient of all the Ti-Si-B sintered alloys. (C) 2013 Elsevier B.V. All rights reserved.

引用

页码：195 / 200

页数：6

共 29 条

[1]

Anders A., 2000, HDB PLASMA IMMERSION, P55

[2] Influence of dynamic densification on nanostructure formation in Ti5Si3 intermetallic alloy and its bulk properties [J].

Counihan, PJ ;

Crawford, A ;

Thadhani, NN .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1999, 267 (01) :26-35

[3]

Fernandes B.B., 2010, THESIS TECHNOLOGICAL

[4] Modification of surface properties of Ti-16Si-4B powder alloy by plasma immersion ion implantation [J].

Fernandes, Bruno Bacci ;

Ueda, Mario ;

Mello, Carina Barros ;

Fernandes, Paulino Bacci ;

Reuther, Helfriecl ;

Ramos, Alfeu Saraiva .

INTERMETALLICS, 2011, 19 (05) :693-697

[5] POWDER-METALLURGY OF TITANIUM-ALLOYS [J].

FROES, FH ;

EYLON, D .

INTERNATIONAL MATERIALS REVIEWS, 1990, 35 (03) :162-182

[6] Microstructure and properties of titanium alloy produced in the newly developed blended elemental powder metallurgy process [J].

Fujita, T ;

Ogawa, A ;

Ouchi, C ;

Tajima, H .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1996, 213 (1-2) :148-153

[7] Titanium alloys for marine application [J].

Gorynin, IV .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1999, 263 (02) :112-116

[8] Characterization of titanium alloy Ti-6Al-4V for chemical, marine and industrial applications [J].

Gurrappa, I .

MATERIALS CHARACTERIZATION, 2003, 51 (2-3) :131-139

[9] Synthesis of alloy Ti-6Al-4V with low residual porosity by a powder metallurgy method [J].

Ivasishin, OM ;

Savvakin, DG ;

Froes, F ;

Mokson, VC ;

Bondareva, KA .

POWDER METALLURGY AND METAL CERAMICS, 2002, 41 (7-8) :382-390

[10] Design of powder metallurgy titanium alloys and composites [J].

Liu, Y ;

Chen, LF ;

Tang, HP ;

Liu, CT ;

Liu, B ;

Huang, BY .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2006, 418 (1-2) :25-35

← 1 2 3 →