Simultaneous identification of residual unbalances and bearing dynamic parameters from impulse responses of rotor-bearing systems

被引:53
作者
Tiwari, R [1 ]
Chakravarthy, V [1 ]
机构
[1] Indian Inst Technol, Dept Mech Engn, Gauhati 781039, India
关键词
rotor-bearing systems; bearing dynamic parameters; identification;
D O I
10.1016/j.ymssp.2006.01.005
中图分类号
TH [机械、仪表工业];
学科分类号
0802 ;
摘要
An identification algorithm for simultaneous estimation of residual unbalances and bearing dynamic parameters by using impulse response measurements is presented for multi-degree-of-freedom (mdofs) flexible rotor-bearing systems. The algorithm identifies speed-dependent bearing dynamic parameters for each bearing and residual unbalances at predefined balancing planes. Bearing dynamic parameters consist of four stiffness and four damping coefficients and residual unbalances contain the magnitude and phase information. Timoshenko beam with gyroscopic effects are included in the system finite element modelling. To overcome the practical difficulty of number of responses that can be measured, the standard condensation is used to reduce the number of degrees of freedom (dofs) of the model. For illustration, responses in time domain are simulated due to impulse forces in the presence of residual unbalances from a rotor-bearing model and transformed to frequency domain. The identification algorithm uses these responses to estimate bearing dynamic parameters along with residual unbalances. The proposed algorithm has the flexibility to incorporate any type and any number of bearings including seals. The identification algorithm has been tested with the measurement noise in the simulated response. Identified parameters match quite well with assumed parameters used for the simulation of responses. The response reproduction capability of identified parameters has been found to be excellent. (c) 2006 Elsevier Ltd. All rights reserved.
引用
收藏
页码:1590 / 1614
页数:25
相关论文
共 50 条
[21]   A method for the estimation of oil film parameters in an asymmetric rotor-bearing system [J].
Chen, Yinsi ;
Liu, Yi ;
Li, Yuan ;
Liu, Heng .
INDUSTRIAL LUBRICATION AND TRIBOLOGY, 2023, 75 (07) :780-788
[22]   Active vibration control of a rotor-bearing system based on dynamic stiffness [J].
Blanco Ortega, Andres ;
Beltran Carbajal, Francisco ;
Silva Navarro, Gerardo ;
Oliver Salazar, Marco Antonio .
REVISTA FACULTAD DE INGENIERIA-UNIVERSIDAD DE ANTIOQUIA, 2010, (55) :125-133
[23]   Bearing parameter identification of rotor-bearing system using clustering-based hybrid evolutionary algorithm [J].
Kim, Yong-Han ;
Yang, Bo-Suk ;
Tan, Andy C. C. .
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION, 2007, 33 (06) :493-506
[24]   Mathematical modeling of continuous multi-stepped rotor-bearing systems [J].
Mereles, Arthur ;
Cavalca, Katia Lucchesi .
APPLIED MATHEMATICAL MODELLING, 2021, 90 :327-350
[25]   Identification of dynamic bearing parameters: A review [J].
Tiwari, R. ;
Lees, A.W. ;
Friswell, M.I. .
Shock and Vibration Digest, 2004, 36 (02) :99-124
[26]   Multiobjective optimum design of rotor-bearing systems with dynamic constraints using immune-genetic algorithm [J].
Choi, BK ;
Yang, BS .
JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME, 2001, 123 (01) :78-81
[27]   Dynamic response analysis of unbalanced rotor-bearing system with internal radial clearance [J].
Patil, V. R. ;
Jadhav, P., V .
SN APPLIED SCIENCES, 2020, 2 (11)
[28]   Condition Monitoring and Identification of Misalignment with Initial Unbalance of Flexible Rotor-Bearing System [J].
Singh, Sankalp ;
Phadatare, Hanmant P. ;
Pratiher, Barun .
MACHINES, MECHANISM AND ROBOTICS, INACOMM 2019, 2022, :1243-1259
[29]   On-site high-speed balancing of flexible rotor-bearing system using virtual trial unbalances at slow run [J].
Ranjan, Gyan ;
Tiwari, Rajiv .
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, 2020, 183
[30]   A novel model-based unbalance monitoring and prognostics for rotor-bearing systems [J].
Lin, Chun-Ling ;
Liang, Jin-Wei ;
Huang, Yi-Mei ;
Huang, Shyh-Chin .
ADVANCES IN MECHANICAL ENGINEERING, 2023, 15 (01)