Drilling-filling friction stir repairing of AZ31B magnesium alloy

被引：22

作者：

Huang, Ruofei ^{[1
]}

Ji, Shude ^{[1
]}

Meng, Xiangchen ^{[1
]}

Li, Zhengwei ^{[1
]}

机构：

[1] Shenyang Aerosp Univ, Fac Aerosp Engn, 37 Daoyi South Ave, Shenyang 110136, Liaoning, Peoples R China

来源：

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY | 2018年 / 255卷

基金：

中国国家自然科学基金;

关键词：

Drilling-filling friction stir repairing; Magnesium alloy; Defect; Microstructure; Microhardness; MECHANICAL-PROPERTIES; ALUMINUM-ALLOY; GRAIN-SIZE; MICROSTRUCTURE; TOOL; PIN; KEYHOLE; JOINT;

D O I：

10.1016/j.jmatprotec.2018.01.019

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Drilling and filling stages were successfully performed to produce a regular volume defect and then repair this fabricated defect. The microhardness distribution of the repaired joint was flat, and an excellent diffusion bonding occurred at the interface between the filler and the base material (BM) under the optimum combinations of a rotational velocity of 1600 rpm, dwell time of 20 s and plunge depth of 0.4 mm. A high-quality joint with the maximum tensile strength of 217 MPa was achieved. The fracture position of this joint was located at the thermo-mechanically affected zone rather than the interface between the filler and the BM of the joint with a low tensile strength.

引用

收藏

页码：765 / 772

页数：8

相关论文

共 19 条

[1]

[Anonymous], 2008, 26502008 GBT STAND A

[2] Experimental study of diffusion welding/bonding of titanium to copper [J].

Aydin, Kemal ;

Kaya, Yakup ;

Kahraman, Nizamettin .

MATERIALS & DESIGN, 2012, 37 :356-368

[3] Achieving ultrafine grain size in Mg-Al-Zn alloy by friction stir processing [J].

Chang, C. I. ;

Du, X. H. ;

Huang, J. C. .

SCRIPTA MATERIALIA, 2007, 57 (03) :209-212

[4] Relationship between grain size and Zener-Holloman parameter during friction stir processing in AZ31 Mg alloys [J].

Chang, CI ;

Lee, CJ ;

Huang, JC .

SCRIPTA MATERIALIA, 2004, 51 (06) :509-514

[5] Optimization of mechanical properties of fine-grained non-combustive magnesium alloy joint by asymmetrical double-sided friction stir welding [J].

Chen, Juan ;

Fujii, Hidetoshi ;

Sun, Yufeng ;

Morisada, Yoshiaki ;

Kondoh, Katsuyoshi .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2017, 242 :117-125

[6] Tensile properties of a friction stir welded magnesium alloy: Effect of pin tool thread orientation and weld pitch [J].

Chowdhury, S. M. ;

Chen, D. L. ;

Bhole, S. D. ;

Cao, X. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2010, 527 (21-22) :6064-6075

[7] Characteristics of friction plug welding to 10 mm thick AA2219-T87 sheet: Weld formation, microstructure and mechanical property [J].

Du, Bo ;

Sun, Zhuanping ;

Yang, Xinqi ;

Cui, Lei ;

Song, Jianling ;

Zhang, Zhongping .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2016, 654 :21-29

[8] Microstructural Evolution of DP980 Steel during Friction Bit Joining [J].

Huang, T. ;

Sato, Y. S. ;

Kokawa, H. ;

Miles, M. P. ;

Kohkonen, K. ;

Siemssen, B. ;

Steel, R. J. ;

Packer, S. .

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2009, 40A (12) :2994-3000

[9] New technique of filling friction stir welding [J].

Huang, Y. X. ;

Han, B. ;

Tian, Y. ;

Liu, H. J. ;

Lv, S. X. ;

Feng, J. C. ;

Leng, J. S. ;

Li, Y. .

SCIENCE AND TECHNOLOGY OF WELDING AND JOINING, 2011, 16 (06) :497-501

[10] New technique for eliminating keyhole by active-passive filling friction stir repairing [J].

Ji, Shude ;

Meng, Xiangchen ;

Zeng, Yaming ;

Ma, Lin ;

Gao, Shuangsheng .

MATERIALS & DESIGN, 2016, 97 :175-182