An investigation of mechanical and metallurgical properties of explosive welded aluminum-dual phase steel

被引：186

作者：

Acarer, Mustafa ^{[1
]}

Demir, Bilge ^{[1
]}

机构：

[1] Karabuk Univ, Fac Tech Educ, Met Educ Dept, Welding Div, Karabuk, Turkey

来源：

MATERIALS LETTERS | 2008年 / 62卷 / 25期

关键词：

dual phase steel; explosive welding; microstructural; mechanical properties;

D O I：

10.1016/j.matlet.2008.05.060

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

The aim of this paper is investigation of microstructure and property relationship in aluminum-HSLA steel and aluminum-dual phase steel bimetals fabricated by explosive welding technique. Dual phase steel was produced by intercritical annealing and water quenching from 1.45Mn-0.2Si-0.186C HSLA steel. Hardness. tensile shear strength. tensile strength, toughness and microstructure of explosively welded aluminum-HSLA steel and aluminum-dual phase steel were evaluated. Both bimetals have a straight bonding interface. It was also seen that plastic deformation of dual phase steel was higher than HSLA steel near interfaces of bimetals. The hardness was increased near the bond interface of bimetals. Tensile and tensile shear strength tests showed that aluminum-dual phase steel is superior than aluminum-HSLA steel. Also, impact toughness of aluminum-dual phase steel was found significantly higher than that of aluminum-HSLA steel. (C) 2008 Elsevier B.V. All rights reserved.

引用

页码：4158 / 4160

页数：3

共 21 条

[11] The effect of new ferrite content on the tensile fracture behaviour of dual phase steels [J].

Erdogan, M .

JOURNAL OF MATERIALS SCIENCE, 2002, 37 (17) :3623-3630

[12]

ERDOGAN M, 2002, MAT SCI TECHNOL, V18, P318

[13] Microstructure-property relationship in explosively welded duplex stainless steel-steel [J].

Kaçar, R ;

Acarer, M .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2003, 363 (1-2) :290-296

[14] Corrosion and mechanical-micro structural aspects of dissimilar joints of Ti-6Al-4V and Al plates [J].

Kahraman, Nizamettin ;

Gulenc, Behcet ;

Findik, Fehim .

INTERNATIONAL JOURNAL OF IMPACT ENGINEERING, 2007, 34 (08) :1423-1432

[15] The effect of annealing treatment on mechanical properties of aluminum clad steel sheet [J].

Manesh, HD ;

Taheri, AK .

MATERIALS & DESIGN, 2003, 24 (08) :617-622

[16] Analysis of the explosive cladding of cu-low carbon steel plates [J].

Raghukandan, K .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2003, 139 (1-3) :573-577

[17] An experimental investigation on the effect of h/D ratio on dynamic form - Cladding of domes [J].

Raghukandan, K ;

Rathinasabapathi, M ;

Vaidyanathan, PV ;

Balasubramanian, V .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 1997, 63 (1-3) :55-59

[18]

RAGHUKANDAN K, 1992, J MATER PROCESS TECH, V32, P65

[19]

Rashid MS, 1976, 760206 SAE, V85, P938

[20] Mechanical properties of a quenched and tempered dual phase steel [J].

Tavares, SSM ;

Pedroza, PD ;

Teodósio, JR ;

Gurova, T .

SCRIPTA MATERIALIA, 1999, 40 (08) :887-892

← 1 2 3 →