Three-dimensional analysis of plastic flow during high-pressure torsion

被引：25

作者：

Figueiredo, Roberto B. ^{[1
]}

de Faria, Gustavo C. V. ^{[2
]}

Cetlin, Paulo R. ^{[2
]}

Langdon, Terence G. ^{[3
,4
,5
]}

机构：

[1] Univ Fed Minas Gerais, Dept Mat Engn & Civil Construct, BR-31270901 Belo Horizonte, MG, Brazil

[2] Univ Fed Minas Gerais, Dept Mech Engn, BR-31270901 Belo Horizonte, MG, Brazil

[3] Univ Southampton, Fac Engn & Environm, Mat Res Grp, Southampton SO17 1BJ, Hants, England

[4] Univ So Calif, Dept Aerosp & Mech Engn, Los Angeles, CA 90089 USA

[5] Univ So Calif, Dept Mat Sci, Los Angeles, CA 90089 USA

来源：

JOURNAL OF MATERIALS SCIENCE | 2013年 / 48卷 / 13期

基金：

欧洲研究理事会;

关键词：

FINITE-ELEMENT-ANALYSIS; MICROSTRUCTURAL EVOLUTION; DEFORMATION-BEHAVIOR; GRAIN-REFINEMENT; HOMOGENEITY; TEMPERATURE; ALUMINUM; EXAMINE; ZONE;

D O I：

10.1007/s10853-012-6979-9

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

The use of imposed plastic deformation as a single parameter to compare results of samples processed by severe plastic deformation is not always accurate. Therefore, this report describes the theoretical plastic flow occurring during high-pressure torsion and presents finite element modeling of this technique to complement the theory. The results demonstrate the influence on plastic flow of the material behavior, the sample aspect ratio, the processing pressure, and the contact friction between the sample and the anvil. It is shown that heterogeneous flow is primarily observed near the edges of the samples. The present results are in general agreement with published experimental observations.

引用

页码：4524 / 4532

页数：9

共 50 条

[21] The significance of strain reversals during processing by high-pressure torsion
Kawasaki, Megumi
Langdon, Terence G.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2008, 498 (1-2): : 341 - 348
[22] An investigation of hardness homogeneity throughout disks processed by high-pressure torsion
Kawasaki, Megumi
Figueiredo, Roberto B.
Langdon, Terence G.
ACTA MATERIALIA, 2011, 59 (01) : 308 - 316
[23] The effect of high-pressure torsion on the microstructure and properties of magnesium
Figueiredo, Roberto B.
Sabbaghianrad, Shima
Langdon, Terence G.
7TH INTERNATIONAL CONFERENCE ON NANOMATERIALS BY SEVERE PLASTIC DEFORMATION, 2017, 194
[24] Developing Hardness and Microstructural Homogeneity in High-Pressure Torsion
Kawasaki, Megumi
Langdon, Terence G.
THERMEC 2011, PTS 1-4, 2012, 706-709 : 1805 - 1810
[25] Microstructural and Hardness Evolution in a Duplex Stainless Steel Processed by High-Pressure Torsion
Ma, Ming
Ding, Hua
Huang, Yi
Tian, Cheng Wei
Langdon, Terence G.
CRYSTALS, 2020, 10 (12): : 1 - 11
[26] An Investigation of Strain-Softening Phenomenon in Al-0.1% Mg Alloy during High-Pressure Torsion Processing
Huang, Yi
Millet, Justine
Zhang, Nian X.
Jenei, Peter
Gubicza, Jeno
Langdon, Terence G.
ADVANCED ENGINEERING MATERIALS, 2020, 22 (10)
[27] Analysis of heterogeneities in strain and microstructure in aluminum alloy and magnesium processed by high-pressure torsion
Panda, Subrata
Toth, Laszlo S.
Fundenberger, Jean-Jacques
Perroud, Olivier
Guyon, Julien
Zou, Jianxin
Grosdidier, Thierry
MATERIALS CHARACTERIZATION, 2017, 123 : 159 - 165
[28] Recrystallization in an Mg-Nd alloy processed by high-pressure torsion: a calorimetric analysis
Bourezg, Yousf Islem
Azzeddine, Hiba
Abib, Khadidja
Huang, Yi
Bradai, Djamel
Langdon, Terence G.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2020, 9 (03): : 3047 - 3054
[29] Analysis of plastic deformation behavior of HDPE during high pressure torsion process
Drai, Ahmed
Aour, Benaoumeur
ENGINEERING STRUCTURES, 2013, 46 : 87 - 93
[30] Influence of Anvil Alignment on Shearing Patterns in High-Pressure Torsion
Huang, Yi
Kawasaki, Megumi
Langdon, Terence G.
ADVANCED ENGINEERING MATERIALS, 2013, 15 (08) : 747 - 755

← 1 2 3 4 5 →