A review on failure characteristics of polymer gear

被引：13

作者：

Ghazali, Wafiuddin Md ^{[1
]}

Idris, Daing Mohamad Nafiz Daing ^{[1
]}

Sofian, Azizul Helmi ^{[2
]}

Siregar, Januar Parlaungan ^{[1
]}

Aziz, Ismail Ali Abdul ^{[1
]}

机构：

[1] Univ Malaysia Pahang, Fac Mech Engn, Pekan 26600, Pahang, Malaysia

[2] Univ Malaysia Pahang, Fac Chem & Nat Resources Engn, Kuantan 26300, Pahang, Malaysia

来源：

2ND INTERNATIONAL CONFERENCE ON AUTOMOTIVE INNOVATION AND GREEN VEHICLE (AIGEV 2016) | 2017年 / 90卷

关键词：

WEAR BEHAVIOR; IMPROVEMENT; ACETAL; DAMAGE; GLASS;

D O I：

10.1051/matecconf/20179001029

中图分类号：

X [环境科学、安全科学];

学科分类号：

08 ; 0830 ;

摘要：

Polymer are now widely used as substitute material for steel gear in low load devices. Its failure differs from gears made of steel, thus it is important to categorize the failures shown by polymer gears. Several previous studies noted that wear detection, microstructure surface condition monitoring, weight loss and temperature detection can be used in detecting failure of polymer gear. This article reviews the failure detection method mentioned above. Other researcher works were studied and their findings were extracted in order to identify the methods they used. The most common method used was wear detection and it was supplemented by other methods such as microstructure surface condition monitoring. Failures shown by polymer can be concluded to be tooth breakage, tooth deformation, material removal and surface fatigue.

引用

页数：10

共 24 条

[1]

A. G. M. Association, 1106A97 A G M ASS

[2]

B. S. Institution, 1987, 6168 BS

[3] WEAR BEHAVIOR OF ACETAL GEAR PAIRS [J].

BREEDS, AR ;

KUKUREKA, SN ;

MAO, K ;

WALTON, D ;

HOOKE, CJ .

WEAR, 1993, 166 (01) :85-91

[4] Applications of dry film lubricants for polymer gears [J].

Dearn, K. D. ;

Hoskins, T. J. ;

Petrov, D. G. ;

Reynolds, S. C. ;

Banks, R. .

WEAR, 2013, 298 :99-108

[5] The use of cooling holes to decrease the amount of thermal damage on a plastic gear tooth [J].

Düzcükoğlu H. ;

Yakut R. ;

Uysal E. .

Journal of Failure Analysis and Prevention, 2010, 10 (06) :545-555

[6] Study on development of polyamide gears for improvement of load-carrying capacity [J].

Duzcukoglu, Hayrettin .

TRIBOLOGY INTERNATIONAL, 2009, 42 (08) :1146-1153

[7]

Elmquist J.L., 2014, Gear Technology, V1, P46

[8] Performance improvement method for Nylon 6 spur gears [J].

Imrek, Hueseyin .

TRIBOLOGY INTERNATIONAL, 2009, 42 (03) :503-510

[9] Durability improvement method for plastic spur gears [J].

Kim, Choong Hyun .

TRIBOLOGY INTERNATIONAL, 2006, 39 (11) :1454-1461

[10] An investigation on the wear behaviour of dissimilar polymer gear engagements [J].

Li, W. ;

Wood, A. ;

Weidig, R. ;

Mao, K. .

WEAR, 2011, 271 (9-10) :2176-2183

← 1 2 3 →