Effect of laser re-melting on electric current assistive sintered CoCrFeNiAlxTiy high entropy alloys: Formation, micro-hardness and wear behaviors

被引：69

作者：

Erdogan, Azmi ^{[1
]}

Doleker, Kadir Mert ^{[2
]}

Zeytin, Sakin ^{[3
]}

机构：

[1] Bartin Univ, Dept Met & Mat Engn, Fac Engn Architecture & Design, Bartin, Turkey

[2] Ondokuz Mayis Univ, Dept Met & Mat Engn, Fac Engn, Samsun, Turkey

[3] Sakarya Univ, Dept Met & Mat Engn, Fac Engn, Sakarya, Turkey

来源：

SURFACE & COATINGS TECHNOLOGY | 2020年 / 399卷

关键词：

High entropy alloy; ECAS; Laser re-melting; Wear; CoCrFeNiAlTi; Intermetallic; MECHANICAL-PROPERTIES; OXIDATION BEHAVIOR; MICROSTRUCTURE; TI; ELEMENTS; AL; DEFORMATION; RESISTANCE; CO;

D O I：

10.1016/j.surfcoat.2020.126179

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

CoCrFeNiAlxTiy high entropy alloys were produced by electric current assistive sintering (ECAS) method and their surfaces were then subjected to laser re-melting. Microstructure, hardness, and wear behaviors were investigated using different parameters. While the CoCrFeNi alloy had FCC and oxide phases after ECAS treatment, only FCC phase was observed after laser re-melting. In addition to the FCC phase, also a BCC phase has been determined with the Al addition. FCC phases disappeared with the laser re-melting effect and the addition of Ti to the alloy. Mixing enthalpy values were found to be effective in microstructure and phase formation. Thanks to the rapid solidification provided by laser re-melting, the phases were distributed homogeneously and in much smaller particle size. Al and Ti elements have contributed positively to the hardness of the CoCrFeNi alloy. With additions of Al and Ti elements, a significant increase in the hardness of CoCrFeNi alloy was obtained. Significant increases in hardness values were observed after laser re-melting due to the smaller dispersion of the phases and the formation of hard phases (BCC/intermetallic). In the hardness values of all alloys, 1.5 times increase was observed by the effect of re-melting. The highest average hardness was determined as 859 Hv in laser re-melted CoCrFeNiAl0.5Ti0.5 alloy. The best wear resistance and the lowest friction coefficient was observed in the laser remelted CoCrFeNiAl0.5Ti0.5 alloy. Laser re-melted alloys exhibited lower volume losses compared to only ECAS-alloys.

引用

页数：9

共 41 条

[21] Laser remelting of plasma-sprayed conventional and nanostructured Al2O3-13 wt.%TiO2 coatings on titanium alloy [J].

Li, Chonggui ;

Wang, You ;

Guo, Lixin ;

He, Junqi ;

Pan, Zhaoyi ;

Wang, Liang .

JOURNAL OF ALLOYS AND COMPOUNDS, 2010, 506 (01) :356-363

[22] Micro-abrasion resistance of thermochemically treated steels in aqueous solutions: Mechanisms, maps, materials selection [J].

Mathew, M. T. ;

Stack, M. M. ;

Matijevic, B. ;

Rocha, L. A. ;

Ariza, E. .

TRIBOLOGY INTERNATIONAL, 2008, 41 (02) :141-149

[23] Hot deformation behaviour and microstructure control in AlCrCuNiFeCo high entropy alloy [J].

Nayan, Niraj ;

Singh, Gaurav ;

Murty, S. V. S. N. ;

Jha, Abhay K. ;

Pant, Bhanu ;

George, Koshy M. ;

Ramamurty, Upadrasta .

INTERMETALLICS, 2014, 55 :145-153

[24]

Orrù R, 2009, MAT SCI ENG R, V63, P127, DOI [10.1016/j.scienta.2008.09.004, 10.1016/j.mser.2008.09.003]

[25] Formation and wear mechanism of tribo-oxides and the regime of oxidational wear of steel [J].

So, H ;

Yu, DS ;

Chuang, CY .

WEAR, 2002, 253 (9-10) :1004-1015

[26] Effect of cryo-deformation on structure and properties of CoCrFeNiMn high-entropy alloy [J].

Stepanov, N. ;

Tikhonovsky, M. ;

Yurchenko, N. ;

Zyabkin, D. ;

Klimova, M. ;

Zherebtsov, S. ;

Efimov, A. ;

Salishchev, G. .

INTERMETALLICS, 2015, 59 :8-17

[27] Effect of V content on microstructure and mechanical properties of the CoCrFeMnNiVx high entropy alloys [J].

Stepanov, N. D. ;

Shaysultanov, D. G. ;

Salishchev, G. A. ;

Tikhonovsky, M. A. ;

Oleynik, E. E. ;

Tortika, A. S. ;

Senkov, O. N. .

JOURNAL OF ALLOYS AND COMPOUNDS, 2015, 628 :170-185

[28] Classification of bulk metallic glasses by atomic size difference, heat of mixing and period of constituent elements and its application to characterization of the main alloying element [J].

Takeuchi, A ;

Inoue, A .

MATERIALS TRANSACTIONS, 2005, 46 (12) :2817-2829

[29] Corrosion behaviour of thermally sprayed Mo added AlCoCrNi high entropy alloy coating [J].

Vallimanalan, A. ;

Babu, S. P. Kumaresh ;

Muthukumaran, S. ;

Murali, M. ;

Gaurav, Vivek ;

Mahendran, R. .

MATERIALS TODAY-PROCEEDINGS, 2020, 27 :2398-2400

[30] MoFe1.5CrTiWAlNbx refractory high-entropy alloy coating fabricated by laser cladding [J].

Wang, Huilin ;

Liu, Qibin ;

Guo, Yaxiong ;

Lan, Hongwei .

INTERMETALLICS, 2019, 115

← 1 2 3 4 5 →