Comparative Study on Microstructural Characteristics and Compression Deformation Behaviour of Alumina and Cenosphere Reinforced Aluminum Syntactic Foam Made Through Stir Casting Technique

被引:26
作者
Mondal, Dehi Pada [1 ]
Goel, Manmohan Dass [1 ,2 ]
Upadhyay, Vartika [1 ]
Das, Satyabrat [1 ]
Singh, Mulayam [1 ]
Barnwal, Ajay Kumar [1 ]
机构
[1] Council Sci & Ind Res CSIR, CSIR Adv Mat & Proc Res Inst AMPRI, Bhopal 462026, India
[2] Visvesvaraya Natl Inst Technol VNIT, Dept Appl Mech, South Ambazari Rd, Nagpur 440010, Maharashtra, India
关键词
Syntactic foam; Compressive deformation; Cenospheres; Microballoons; Plastic collapse; POWDER-METALLURGY;
D O I
10.1007/s12666-017-1211-x
中图分类号
TF [冶金工业];
学科分类号
0806 ;
摘要
In order to examine the effect of microballoons type on microstructure and compressive deformation behaviour of aluminum syntactic foam, alumina reinforced and cenosphere reinforced aluminum syntactic foams have been made through stir-casting technique. Alumina microballoons reinforced aluminum syntactic foam (AMRASF) has been developed using stir casting technique. Volume fraction of alumina microballoons in AMRASF varies in the range of 0.39-0.74. The compressive deformation behavior of these AMRASF is compared with that of cenosphere reinforced aluminum syntactic foam (CPRASF). The AMRASF does not exhibit clear plastic collapse stage as observed in case of CPRSAF. It is further noted that AMRASF shows the existence of work hardening phenomena after yielding but CPRASF does not show any significant work hardening after yielding even at higher relative densities of foam. This is explained on the basis of characteristics of alumina microballoons and cenospheres and interface characteristics between matrix and respective microballoons used. Effect of individual microballoons' characteristics on the foam properties has also been explained.
引用
收藏
页码:567 / 577
页数:11
相关论文
共 17 条
[1]   Foaming behavior of powder metallurgical Al-Sn foams [J].
Aguirre-Perales, Lydia Y. ;
Jung, In-Ho ;
Drew, Robin A. L. .
ACTA MATERIALIA, 2012, 60 (02) :759-769
[2]   Fabrication, microstructure and compressive behavior of ZC63 Mg-microballoon foam composites [J].
Daoud, A. ;
Abou El-Khair, M. T. ;
Abdel-Aziz, M. ;
Rohatgi, P. .
COMPOSITES SCIENCE AND TECHNOLOGY, 2007, 67 (09) :1842-1853
[3]   Effect of strain rate on compressive properties of novel Zn12Al based composite foams containing hybrid pores [J].
Daoud, A. .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2009, 525 (1-2) :7-17
[4]   Strain rate sensitivity of closed cell aluminium fly ash foam [J].
Dass Goel, Manmohan ;
Matsagar, Vasant A. ;
Gupta, Anil K. ;
Marburg, Steffen .
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA, 2013, 23 (04) :1080-1089
[5]   Effect of strain rate and relative density on compressive deformation behavior of aluminum cenosphere syntactic foam [J].
Goel, M. D. ;
Mondal, D. P. ;
Yadav, M. S. ;
Gupta, S. K. .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2014, 590 :406-415
[6]   Dynamic compression behavior of cenosphere aluminum alloy syntactic foam [J].
Goel, Manmohan Dass ;
Peroni, Marco ;
Solomos, George ;
Mondal, Dehi Pada ;
Matsagar, Vasant A. ;
Gupta, Anil K. ;
Larcher, Martin ;
Marburg, Steffen .
MATERIALS & DESIGN, 2012, 42 :418-423
[7]   Titanium cenosphere syntactic foam with coarser cenosphere fabricated by powder metallurgy at lower compaction load [J].
Jha, N. ;
Mondal, D. P. ;
Goel, M. D. ;
Majumdar, J. D. ;
Das, S. ;
Modi, O. P. .
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA, 2014, 24 (01) :89-99
[8]   Synthesis And Characterization Of Al Foam, Al Alloy Foam And Al-SiC Composite Foam [J].
Khan, K. L. A. ;
Mahajan, P. ;
Prasad, R. .
TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS, 2008, 61 (2-3) :111-113
[9]  
Khedle R, 2011, CMC COM MAT CONT, V27, P211
[10]   High temperature compressive deformation behaviour of aluminum syntactic foam [J].
Mondal, D. P. ;
Jha, Nidhi ;
Badkul, Anshul ;
Das, S. ;
Khedle, Raghavendra .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2012, 534 :521-529