An Experimental Study of the Effect of the Cutting Conditions on Tool Edge Wear in High-speed Machining of Ti-6Al-4V

被引：0

作者：

Fang, N. ^{[1
]}

Pai, P. Srinivasa ^{[1
]}

Edwards, N. ^{[1
]}

机构：

[1] Utah State Univ, Coll Engn, Logan, UT 84322 USA

来源：

4TH INTERNATIONAL CONFERENCE ON MATERIALS ENGINEERING FOR ADVANCED TECHNOLOGIES (ICMEAT 2015) | 2015年

关键词：

TITANIUM-ALLOYS; MACHINABILITY; TI6AL4V;

D O I：

暂无

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

This paper focuses on an experimental study of how the cutting conditions affect tool edge wear (i.e., the wear of a tool cutting edge before it is fully worn away) in high-speed machining of an advanced titanium alloy Ti-6Al-4V. The results show that tool edge wear is a dynamic process and increases with increasing cutting speed or with increasing feed rate. Depending on the cutting conditions, the dominated pattern of tool wear can gradually shift from tool edge wear to the tool crater wear, or to the tool flank wear.

引用

收藏

页码：56 / 59

页数：4

相关论文

共 11 条

[1] Finite element simulation of high-speed machining of titanium alloy (Ti-6Al-4V) based on ductile failure model [J].

Chen, Guang ;

Ren, Chengzu ;

Yang, Xiaoyong ;

Jin, Xinmin ;

Guo, Tao .

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2011, 56 (9-12) :1027-1038

[2] Tool life and wear mechanisms in high speed machining of Ti-6Al-4V alloy with PCD tools under various coolant pressures [J].

da Silva, Rosemar B. ;

Machado, Alisson R. ;

Ezugwu, Emmanuel O. ;

Bonney, John ;

Sales, Wisley F. .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2013, 213 (08) :1459-1464

[3] Effect of tool edge wear on the cutting forces and vibrations in high-speed finish machining of Inconel 718: an experimental study and wavelet transform analysis [J].

Fang, Ning ;

Pai, P. Srinivasa ;

Mosquea, S. .

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2011, 52 (1-4) :65-77

[4] Blend of sharpness and strength on a ball nose endmill geometry for high speed machining of Ti6Al4V [J].

Kuppuswamy, Ramesh ;

Bower, Deon ;

March, Poloko .

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2014, 70 (9-12) :1827-1834

[5] Wear performance of (nc-AlTiN)/(a-Si3N4) coating and (nc-AlCrN)/(a-Si3N4) coating in high-speed machining of titanium alloys under dry and minimum quantity lubrication (MQL) conditions [J].

Liu, Zhiqiang ;

An, Qinglong ;

Xu, Jinyang ;

Chen, Ming ;

Han, Shu .

WEAR, 2013, 305 (1-2) :249-259

[6] Influence of Tool Materials on Machinability of Titanium- and Nickel-Based Alloys: A Review [J].

Pervaiz, Salman ;

Rashid, Amir ;

Deiab, Ibrahim ;

Nicolescu, Mihai .

MATERIALS AND MANUFACTURING PROCESSES, 2014, 29 (03) :219-252

[7]

Veiga C, 2013, REV ADV MATER SCI, V34, P148

[8] Investigations on the chip formation mechanism and shear localization sensitivity of high-speed machining Ti6Al4V [J].

Wang, Bing ;

Liu, Zhanqiang .

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2014, 75 (5-8) :1065-1076

[9]

Wu Q, 2006, T NAMRI SME, V34, P397

[10] Modeling periodic adiabatic shear band evolution during high speed machining Ti-6Al-4V alloy [J].

Ye, G. G. ;

Xue, S. F. ;

Jiang, M. Q. ;

Tong, X. H. ;

Dai, L. H. .

INTERNATIONAL JOURNAL OF PLASTICITY, 2013, 40 :39-55