Investigation on the burr formation mechanism in micro cutting

被引：83
|
作者：
Wu, Xian [1 ]
Li, Liang [1 ]
He, Ning [1 ]
机构：
[1] Nanjing Univ Aeronaut & Astronaut, Coll Mech & Elect Engn, Nanjing, Jiangsu, Peoples R China
来源：
PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY | 2017年 / 47卷
基金：
中国国家自然科学基金;
关键词：
Micro cutting; Burr formation; Stress distribution; Cutting edge radius; RAKE ANGLE; THICKNESS; SIZE;
D O I：
10.1016/j.precisioneng.2016.08.004
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
It is desirable to minimize burr formation for improving part quality. This paper presents an investigation on the burr formation mechanism in micro cutting by taking into consideration the stress distribution around the cutting edge arc. The influences of the uncut chip thickness and the cutting edge radius on burr formation were investigated. Poisson burr is attributed to the side flow of the stagnation material at the bottom of the cutting edge arc. The stress distribution at the cutting edge arc has great influence on Poisson burr formation. The burr height decreases to the minimum value and then increases with reducing the uncut chip thickness due to the change of the maximum stress distribution. An optimum machining strategy also is suggested in micro milling of snake-shaped groove microstructure. (C) 2016 Elsevier Inc. All rights reserved.
引用
收藏
页码：191 / 196
页数：6
相关论文
共 50 条
  • [31] Analysis of fracture in burr formation at the exit stage of metal cutting
    Ko, SL
    Dornfeld, DA
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 1996, 58 (2-3) : 189 - 200
  • [32] Burr Formation in Metal Cutting Operations and Some Deburring Methods
    Kodacsy, Janos
    Szabo, Andras
    PRECISION MACHINING VII, 2014, 581 : 235 - 240
  • [33] Finite Element Modeling of Burr Formation in Orthogonal Metal Cutting
    Deng, W. J.
    Li, C.
    Xia, W.
    Wei, X. Z.
    SURFACE FINISHING TECHNOLOGY AND SURFACE ENGINEERING, 2008, 53-54 : 71 - +
  • [34] Experimental research on the top burr formation in micro milling
    Xian Wu
    Mingyang Du
    Jianyun Shen
    Feng Jiang
    Yuan Li
    Li Liu
    The International Journal of Advanced Manufacturing Technology, 2021, 117 : 3477 - 3486
  • [35] Experimental research on the top burr formation in micro milling
    Wu, Xian
    Du, Mingyang
    Shen, Jianyun
    Jiang, Feng
    Li, Yuan
    Liu, Li
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2021, 117 (11-12) : 3477 - 3486
  • [36] Investigation on formation mechanism of the burrs during abrasive reaming based on the single-particle abrasive micro-cutting behavior
    Changyong Yang
    Jianzhong Huang
    Jiuhua Xu
    Wenfeng Ding
    Yucan Fu
    Shaowu Gao
    The International Journal of Advanced Manufacturing Technology, 2021, 113 : 907 - 921
  • [37] Investigation on formation mechanism of the burrs during abrasive reaming based on the single-particle abrasive micro-cutting behavior
    Yang, Changyong
    Huang, Jianzhong
    Xu, Jiuhua
    Ding, Wenfeng
    Fu, Yucan
    Gao, Shaowu
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2021, 113 (3-4) : 907 - 921
  • [38] Finite element modeling of burr formation in metal cutting with a backup material
    Deng, W. J.
    Xia, W.
    Lu, L. S.
    Tang, Y.
    PRECISION SURFACE FINISHING AND DEBURRING TECHNOLOGY, 2007, 24-25 : 71 - 76
  • [39] Finite element simulation for burr formation near the exit of orthogonal cutting
    Deng, W. J.
    Xia, W.
    Tang, Y.
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2009, 43 (9-10) : 1035 - 1045
  • [40] BURR FORMATION AT THE INTERFACE DURING BI-MATERIAL ORTHOGONAL CUTTING
    Poissenot-Arrigoni, C.
    Fromentin, G.
    Poulachon, G.
    Marcon, B.
    Legrand, C.
    MM SCIENCE JOURNAL, 2021, 2021 : 5254 - 5258
12345