Effect of Modifiers on Injection Molding of Waste Polyethylene Drip Tape

被引：0
|
作者：
Guo, Bin [1 ]
Wu, Shou-Jun [1 ]
Zhu, De-Lan [1 ]
机构：
[1] Northwest A&F Univ, Coll Water Resources & Architectural Engn, Yangling 712100, Shaanxi, Peoples R China
来源：
PROCEEDINGS OF THE 2015 INTERNATIONAL CONFERENCE ON MATERIAL SCIENCE AND APPLICATIONS (ICMSA 2015) | 2015年 / 3卷
关键词：
Polyethylene; Injection Molding; Ethylene-vinyl Acetate Copolymer; Dicumyl Peroxide; MECHANICAL-PROPERTIES; CROSS-LINKING; BLENDS;
D O I：
暂无
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
In this work, effects of Ethylene-vinyl acetate copolymer (EVA) and Dicumyl peroxide (DCP) on injection molding of recycled polyethylene (PE) materials obtained from a waste disposable drip tape are studied. Under injected at 175-230 degrees C and 35-40 MPa, the recycled PE materials with EVA showed good injection moldability, while those with DCP showed poor injection moldability with DCP introduction increasing. Under injected at 135-145 degrees C and 50-60 MPa, the recycled PE materials with DCP can be well injection molded.
引用
收藏
页码：948 / 951
页数：4
相关论文
共 50 条
  • [21] The effect of vibration injection molding on mechanical properties of polyolefin parts
    Yan, Z
    Shen, KZ
    Zhang, J
    JOURNAL OF APPLIED POLYMER SCIENCE, 2004, 91 (03) : 1514 - 1518
  • [22] Effects of Three Different Injection-Molding Methods on the Mechanical Properties and Electrical Conductivity of Carbon Nanotube/Polyethylene/Polyamide 6 Nanocomposite
    Mi, Dashan
    Zhao, Zhongguo
    Zhu, Wenli
    POLYMERS, 2019, 11 (11)
  • [23] High speed injection molding of high density polyethylene - Effects of injection speed on structure and properties
    Jiang, Kun
    Yu, Fei-long
    Su, Run
    Yang, Jing-hui
    Zhou, Tian-nan
    Gao, Jian
    Deng, Hua
    Wang, Ke
    Zhang, Qin
    Chen, Feng
    Fu, Qiang
    CHINESE JOURNAL OF POLYMER SCIENCE, 2011, 29 (04) : 456 - 464
  • [24] Effect of a Tie Film on the Enhanced Interfacial Adhesion Between Polyethylene and Polyamide-6 in a Sequential Injection Molding
    Jiang, Genjie
    Wu, Hong
    Yan, Bowen
    Guo, Shaoyun
    POLYMER ENGINEERING AND SCIENCE, 2010, 50 (04): : 719 - 729
  • [25] Empirical Models for End-Use Properties Prediction: Application to Injection Molding of Some Polyethylene Resins
    Costa, M. C. B.
    Jardini, A. L.
    Lima, N. M. N.
    Embirucu, M.
    Maciel, M. R. Wolf
    Maciel Filho, R.
    JOURNAL OF APPLIED POLYMER SCIENCE, 2009, 114 (06) : 3780 - 3792
  • [26] An effect of mold surface temperature on final product properties in the injection molding of high-density polyethylene materials
    İdris Karagöz
    Polymer Bulletin, 2021, 78 : 2627 - 2644
  • [27] An effect of mold surface temperature on final product properties in the injection molding of high-density polyethylene materials
    Karagoz, Idris
    POLYMER BULLETIN, 2021, 78 (05) : 2627 - 2644
  • [28] Thin-wall injection molding of high-density polyethylene for infrared radiation system lenses
    Kaneda, Ryo
    Takahashi, Toshihiro
    Takiguchi, Masayasu
    Hijikata, Motoharu
    Ito, Hiroshi
    JOURNAL OF POLYMER ENGINEERING, 2018, 38 (03) : 307 - 313
  • [29] The effect of mold temperature on chemical foaming of injection molded recycled polyethylene-terephthalate
    Ronkay, Ferenc
    Molnar, Bela
    Dogossy, Gabor
    THERMOCHIMICA ACTA, 2017, 651 : 65 - 72
  • [30] The effect of limescale on heat transfer in injection molding
    Zink, Bela
    Kovacs, Jozsef Gabor
    INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER, 2017, 86 : 101 - 107
12345