Effect of Modifiers on Injection Molding of Waste Polyethylene Drip Tape

被引：0
|
作者：
Guo, Bin [1 ]
Wu, Shou-Jun [1 ]
Zhu, De-Lan [1 ]
机构：
[1] Northwest A&F Univ, Coll Water Resources & Architectural Engn, Yangling 712100, Shaanxi, Peoples R China
来源：
PROCEEDINGS OF THE 2015 INTERNATIONAL CONFERENCE ON MATERIAL SCIENCE AND APPLICATIONS (ICMSA 2015) | 2015年 / 3卷
关键词：
Polyethylene; Injection Molding; Ethylene-vinyl Acetate Copolymer; Dicumyl Peroxide; MECHANICAL-PROPERTIES; CROSS-LINKING; BLENDS;
D O I：
暂无
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
In this work, effects of Ethylene-vinyl acetate copolymer (EVA) and Dicumyl peroxide (DCP) on injection molding of recycled polyethylene (PE) materials obtained from a waste disposable drip tape are studied. Under injected at 175-230 degrees C and 35-40 MPa, the recycled PE materials with EVA showed good injection moldability, while those with DCP showed poor injection moldability with DCP introduction increasing. Under injected at 135-145 degrees C and 50-60 MPa, the recycled PE materials with DCP can be well injection molded.
引用
收藏
页码：948 / 951
页数：4
相关论文
共 50 条
  • [1] Injection Molding of Low-Density Polyethylene (LDPE) as a Model Polymer: Effect of Molding Parameters on the Microstructure and Crystallinity
    Leyva-Porras, Cesar
    Balderrama-Aguilar, Andrea
    Estrada-Avila, Yael
    Espelosin-Gomez, Inaki
    Mendoza-Duarte, Monica
    Pinon-Balderrama, Claudia
    Zenaida Saavedra-Leos, Maria
    Estrada-Moreno, Ivan
    POLYMERS, 2021, 13 (20)
  • [2] On the use of low-density polyethylene as disposable drip tape for field irrigation
    Zhu, Delan
    Wu, Shoujun
    Guo, Bin
    PLASTICS RUBBER AND COMPOSITES, 2018, 47 (03) : 133 - 137
  • [3] Investigation of polymer injection molding using calcareous waste concrete powder and polyethylene
    Kanda, Yasuyuki
    Kusumoto, Tsuguri
    POLYMER COMPOSITES, 2024,
  • [4] Mold replication in injection molding of high density polyethylene
    Quadrini, Fabrizio
    Bellisario, Denise
    Santo, Loredana
    Bottini, Luana
    Boschetto, Alberto
    POLYMER ENGINEERING AND SCIENCE, 2020, 60 (10): : 2459 - 2469
  • [5] Injection Molding of Thermoplastic Cellulose Esters and Their Compatibility with Poly(Lactic Acid) and Polyethylene
    Willberg-Keyrilainen, Pia
    Orelma, Hannes
    Ropponen, Jarmo
    MATERIALS, 2018, 11 (12)
  • [6] Alternating multilayer structure of polyethylene/polypropylene blends obtained through injection molding
    Jiang, Kun
    Yu, Feilong
    Bai, Hongwei
    Gao, Jian
    Deng, Hua
    Zhang, Qin
    Fu, Qiang
    JOURNAL OF APPLIED POLYMER SCIENCE, 2012, 124 (06) : 4452 - 4456
  • [7] The Microcellular Injection Molding of Low-Density Polyethylene (LDPE) Composites
    Lee, Jungjoo
    Turng, Lih-Sheng
    Kramschuster, Adam
    POLYMER-PLASTICS TECHNOLOGY AND ENGINEERING, 2010, 49 (13) : 1339 - 1346
  • [8] Study of the effect of organic clay on the shear-induced crystallization of high-density polyethylene through dynamic-packing injection molding
    Deng, Cong
    Gao, Xueqin
    Chen, Zhanchun
    Xue, Shan
    Shen, Kaizhi
    POLYMER INTERNATIONAL, 2010, 59 (12) : 1660 - 1664
  • [9] Recycling carpet waste by injection and compression molding
    Zhang, Y
    Muzzy, JD
    Kumar, S
    POLYMER-PLASTICS TECHNOLOGY AND ENGINEERING, 1999, 38 (03) : 485 - 498
  • [10] Development of slate fiber reinforced high density polyethylene composites for injection molding
    Carbonell-Verdu, A.
    Garcia-Garcia, D.
    Jorda, A.
    Samper, M. D.
    Balart, R.
    COMPOSITES PART B-ENGINEERING, 2015, 69 : 460 - 466
12345