Effects of intergranular carbide precipitation on delayed fracture behavior in three TWinning Induced Plasticity (TWIP) steels

被引：37
作者：
Hong, Seokmin [1 ]
Lee, Junghoon [1 ]
Lee, Byeong-Joo [1 ]
Kim, Hyoung Seop [1 ]
Kim, Sung-Kyu [2 ]
Chin, Kwang-Geun [2 ]
Lee, Sunghak [1 ]
机构：
[1] Pohang Univ Sci & Technol, Ctr Adv Aerosp Mat, Pohang 790784, South Korea
[2] POSCO, Tech Res Labs, High Manganese Sheet Steel Project Team, Gwangyang 545711, South Korea
来源：
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2013年 / 587卷
关键词：
TWIP steels; Intergranular carbide; Delayed fracture; Intergranular fracture; FE-MN-C; HYDROGEN; AL; ALUMINUM; GRAIN; MICROSTRUCTURE; TRANSFORMATION; CRACKING; BORON; EMBRITTLEMENT;
D O I：
10.1016/j.msea.2013.08.063
中图分类号：
TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
The delayed fracture behavior related with intergranular carbide precipitation of three TWinning Induced Plasticity (TWIP) steels was investigated. According to the microstructural analysis, nanosized (Fe,Mn)(3)C cementites were precipitated along grain boundaries in the 0.6C-22Mn and 0.6C-18Mn steels, whereas their precipitation was hardly observed in the 0.6C-18Mn-2Al steel, which was confirmed by equilibrium phase diagrams calculated from a ThermoCalc program. When cup specimens were dipped in the boiled water, the 0.6C-22Mn, 0.6C-18Mn, and 0.6C-18Mn-2Al steel cups were cracked after 5.5, 15, and 169 h, respectively. The delayed fracture regions consisted of intergranular facets, and the tendency of intergranular facture decreased in the order of 0.6C-22Mn, 0.6C-18Mn, and 0.6C-18Mn-2Al steels. Thus, the delayed fracture behavior was closely related with the intergranular fracture mode caused by grain boundary cementites. The addition of Al remarkably increased the resistance to delayed fracture because it suppressed the formation of grain boundary cementites and reduced the residual stresses in the cup specimen. (C) 2013 Elsevier B.V. All rights reserved.
引用
收藏
页码：85 / 99
页数：15
相关论文
共 46 条
[1]   A physical model of the twinning-induced plasticity effect in a high manganese austenitic steel [J].
Allain, S ;
Chateau, JP ;
Bouaziz, O .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2004, 387 :143-147
[2]  
[Anonymous], 1999, TCFE2000 THERMOCALC
[3]   Delayed cracking in 301LN austenitic steel after deep drawing: Martensitic transformation and residual stress analysis [J].
Berrahmoune, M. R. ;
Berveiller, S. ;
Inal, K. ;
Patoor, E. .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2006, 438 :262-266
[4]  
Bhadeshia H., 2006, STEELS, Vthird
[5]   Effect of grain and twin boundaries on the hardening mechanisms of twinning-induced plasticity steels [J].
Bouaziz, O. ;
Allain, S. ;
Scott, C. .
SCRIPTA MATERIALIA, 2008, 58 (06) :484-487
[6]   High manganese austenitic twinning induced plasticity steels: A review of the microstructure properties relationships [J].
Bouaziz, O. ;
Allain, S. ;
Scott, C. P. ;
Cugy, P. ;
Barbier, D. .
CURRENT OPINION IN SOLID STATE & MATERIALS SCIENCE, 2011, 15 (04) :141-168
[7]   Modelling of TWIP effect on work-hardening [J].
Bouaziz, O ;
Guelton, N .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2001, 319 :246-249
[8]   Effects of Al addition on deformation and fracture mechanisms in two high manganese TWIP steels [J].
Chin, Kwang-Geun ;
Kang, Chung-Yun ;
Shin, Sang Yong ;
Hong, Seokmin. ;
Lee, Sunghak ;
Kim, Hyoung Seop ;
Kim, Kyung-hun ;
Kim, Nack J. .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2011, 528 (06) :2922-2928
[9]   Thermodynamic calculation on the stability of (Fe,Mn)3AlC carbide in high aluminum steels [J].
Chin, Kwang-Geun ;
Lee, Hyuk-Joong ;
Kwak, Jai-Hyun ;
Kang, Jung-Yoon ;
Lee, Byeong-Joo .
JOURNAL OF ALLOYS AND COMPOUNDS, 2010, 505 (01) :217-223
[10]   Microstructural change in austenitic Fe-30.0wt%Mn-7.8wt%Al-1.3wt%C initiated by spinodal decomposition and its influence on mechanical properties [J].
Choo, WK ;
Kim, JH ;
Yoon, JC .
ACTA MATERIALIA, 1997, 45 (12) :4877-4885
12345