Direct extraction of rate-dependent traction-separation laws for polyurea/steel interfaces

被引：118

作者：

Zhu, Yong ^{[2
]}

Liechti, Kenneth M. ^{[1
]}

Ravi-Chandar, K. ^{[1
]}

机构：

[1] Univ Texas Austin, Res Ctr Mech Solids Struct & Mat, Austin, TX 78712 USA

[2] N Carolina State Univ, Dept Mech & Aerosp Engn, Raleigh, NC 27695 USA

来源：

INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES | 2009年 / 46卷 / 01期

关键词：

Polyurea; Adhesion; Interfacial fracture; Cohesive zone model; Traction-separation law; COHESIVE-ZONE MODELS; MIXED-MODE; CRACK-PROPAGATION; NOTCH SENSITIVITY; FRACTURE; DELAMINATION; TOUGHNESS; PLASTICITY; STRENGTH; BEHAVIOR;

D O I：

10.1016/j.ijsolstr.2008.08.019

中图分类号：

O3 [力学];

学科分类号：

08 ; 0801 ;

摘要：

Polyurea coatings on steel form tough, flexible and chemically resistant surfaces, making them ideal for a variety of applications. An important issue for polyurea coatings in some cases is their adhesion to steel under various loading conditions in aggressive environments. In this paper, adhesion was examined using steel/polyurea/steel sandwich specimens and interfacial fracture mechanics. The mode I and mode 2 interfacial fracture behaviors were characterized by two independent traction-separation laws. The traction-separation laws were measured directly by recording the j-integral and the end-opening displacement in the directions normal and tangential to the steel/polyurea interface. In each case, the traction was initially nonzero, increased with increasing separation, reached its peak value and then decreased with further increasing opening. Strong rate-dependent effects were found for both modes of fracture and were attributed to the interfacial behavior. Porosity introduced during the processing of the polyurea affected the traction-separation laws and associated fracture mechanisms. (c) 2008 Elsevier Ltd. All rights reserved.

引用

页码：31 / 51

页数：21

共 48 条

[21] Use of a cohesive-zone model to analyze the fracture of a fiber-reinforced polymer-matrix composite [J].

Li, S ;

Thouless, MD ;

Waas, AM ;

Schroeder, JA ;

Zavattieri, PD .

COMPOSITES SCIENCE AND TECHNOLOGY, 2005, 65 (3-4) :537-549

[22] Use of mode-I cohesive-zone models to describe the fracture of an adhesively-bonded polymer-matrix composite [J].

Li, S ;

Thouless, MD ;

Waas, AM ;

Schroeder, JA ;

Zavattieri, PD .

COMPOSITES SCIENCE AND TECHNOLOGY, 2005, 65 (02) :281-293

[23] Mixed-mode cohesive-zone models for fracture of an adhesively bonded polymer-matrix composite [J].

Li, S ;

Thouless, MD ;

Waas, AM ;

Schroeder, JA ;

Zavattieri, PD .

ENGINEERING FRACTURE MECHANICS, 2006, 73 (01) :64-78

[24] EXPERIMENTAL-DETERMINATION OF THE TENSION-SOFTENING RELATIONS FOR CEMENTITIOUS COMPOSITES [J].

LI, VC ;

CHAN, CM ;

LEUNG, CKY .

CEMENT AND CONCRETE RESEARCH, 1987, 17 (03) :441-452

[25] CRACK-PROPAGATION AT MATERIAL INTERFACES .2. EXPERIMENTS ON MODE INTERACTION [J].

LIECHTI, KM ;

KNAUSS, WG .

EXPERIMENTAL MECHANICS, 1982, 22 (10) :383-391

[26]

Liechti KM, 2001, J MECH PHYS SOLIDS, V49, P1039

[27] Characterizing mode II delamination cracks in stitched composites [J].

Massabò, R ;

Mumm, DR ;

Cox, BN .

INTERNATIONAL JOURNAL OF FRACTURE, 1998, 92 (01) :1-38

[28] The effect of self-assembled monolayers on interfacial fracture [J].

Mello, Alberto W. ;

Liechti, Kenneth M. .

JOURNAL OF APPLIED MECHANICS-TRANSACTIONS OF THE ASME, 2006, 73 (05) :860-870

[29] Cohesive zone modeling of crack nucleation at bimaterial corners [J].

Mohammed, I ;

Liechti, KM .

JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS, 2000, 48 (04) :735-764

[30] AN ANALYSIS OF TENSILE DECOHESION ALONG AN INTERFACE [J].

NEEDLEMAN, A .

JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS, 1990, 38 (03) :289-324

← 1 2 3 4 5 →