Influence of Point Angle on Drill Hole Quality and Machining Forces when Drilling CFRP

被引:96
作者
Heisel, Uwe [1 ]
Pfeifroth, Tobias [1 ]
机构
[1] Univ Stuttgart, Inst Machine Tools, D-70174 Stuttgart, Germany
来源
FIFTH CIRP CONFERENCE ON HIGH PERFORMANCE CUTTING 2012 | 2012年 / 1卷
关键词
Drilling; Composite; Quality; Tool design; CFRP; DELAMINATION;
D O I
10.1016/j.procir.2012.04.084
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
This paper presents the results of investigations concerning the influence of the point angle of a drill tool and increased cutting speeds on machining forces and drill hole quality (delamination, fraying, burr formation). Elevated point angles result in increased feed force F-f while the drilling torque T-d stays almost constant. The assessment of characteristics concerning drill holes show that the quality at the entrance is best when using point angles > 180 degrees, while it is poor at the exit. The increase in cutting speed leads to almost no differences in drill hole quality but does lead to rising feed forces and decreasing drilling torques. (C) 2012 The Authors. Published by Elsevier B. V. Selection and/or peer-review under responsibility of Professor Konrad Wegener
引用
收藏
页码:471 / 476
页数:6
相关论文
共 50 条
[21]   Effects of drilling conditions, drill material and point angle on acoustic emission and hole exit delamination in drilling advanced fiber reinforced composites [J].
Okafor, AC ;
Birdsong, SR .
PROCESS CONTROL AND SENSORS FOR MANUFACTURING II, 1999, 3589 :101-114
[22]   Influence of machining parameters and new nano-coated tool on drilling performance of CFRP/Aluminium sandwich [J].
Zitoune, Redouane ;
Krishnaraj, Vijayan ;
Almabouacif, Belkacem Sofiane ;
Collombet, Francis ;
Sima, Michal ;
Jolin, Alain .
COMPOSITES PART B-ENGINEERING, 2012, 43 (03) :1480-1488
[23]   Influence of machining parameters and tool structure on cutting force and hole wall damage in drilling CFRP with stepped drills [J].
Qiu, Xinyi ;
Li, Pengnan ;
Niu, Qiulin ;
Chen, Anhua ;
Ouyang, Puren ;
Li, Changping ;
Ko, Tae Jo .
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2018, 97 (1-4) :857-865
[24]   Assessment of Hole Quality and Thrust Force when Drilling CFRP/AI Stack using Carbide Tools [J].
Ashrafi, Sina Alizadeh ;
Sharif, Safian ;
Yahya, Mohd Yazid ;
Davoudinejad, Ali .
APPLIED MECHANICS AND INDUSTRIAL TECHNOLOGIES, 2012, 234 :28-33
[25]   Influence of hole quality on fatigue life of drilled CFRP with the different ply orientation angle [J].
Yenigun, Burak ;
Kilickap, Erol .
JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING, 2021, 43 (01)
[26]   ROTARY ULTRASONIC MACHINING: EFFECTS OF TOOL END ANGLE ON DELAMINATION OF CFRP DRILLING [J].
Fernando, Palamandadige K. S. C. ;
Zhang, Meng ;
Pei, Zhijian ;
Cong, Weilong .
PROCEEDINGS OF THE ASME 12TH INTERNATIONAL MANUFACTURING SCIENCE AND ENGINEERING CONFERENCE - 2017, VOL 1, 2017,
[27]   Influence of hole quality on fatigue life of drilled CFRP with the different ply orientation angle [J].
Burak Yenigun ;
Erol Kilickap .
Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2021, 43
[28]   Assessment on Hole Quality During Drilling of Al/CFRP Stack [J].
Barik, Tarakeswar ;
Sarangi, Swagatika ;
Pal, Kamal .
ADVANCES IN UNCONVENTIONAL MACHINING AND COMPOSITES, AIMTDR 2018, 2020, :757-770
[29]   Experimental analysis on the influence of graphene nanoplatelets in CFRP composite to explore the hole quality during drilling [J].
Thakur, Raju Kumar ;
Singh, Kalyan Kumar ;
Mahesh, Prashant ;
Rawat, Prashant ;
Sawai, Nandkishor .
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE, 2025,
[30]   Influence of cooling air direction on tool wear and hole quality in CFRP drilling [J].
Wang F. ;
Cheng D. ;
Zhao M. ;
Fu R. .
Fuhe Cailiao Xuebao/Acta Materiae Compositae Sinica, 2019, 36 (02) :410-417