High temperature air oxidation behavior of Hastelloy X processed by Electron Beam Melting (EBM) and Selective Laser Melting (SLM)

被引：40
|
作者：
Romedenne, M. [1 ]
Pillai, R. [1 ]
Kirka, M. [1 ]
Dryepondt, S. [1 ]
机构：
[1] Oak Ridge Natl Lab, Mat Sci & Technol Div, Oak Ridge, TN 37831 USA
来源：
CORROSION SCIENCE | 2020年 / 171卷
关键词：
Oxidation; Ni-based alloy; Selective Laser Melting; Electron Beam Melting; LAVES PHASE-FORMATION; MECHANICAL-PROPERTIES; ALLOY; TEXTURE; MICROSTRUCTURE; SCALES; HETEROGENEITY; STRATEGIES; DEPOSITION; RESISTANCE;
D O I：
10.1016/j.corsci.2020.108647
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
The microstructure and oxidation behavior of Laser Beam Melted, Electron Beam Melted and wrought Hastelloy X were studied at 950 degrees C in dry air, 50 h cycles, up to 1000 h. The variability of processing parameters and powder compositions strongly impacted the oxidation and spallation behavior. The alloys with high Mn and Si were associated with higher oxidation rates, finer Cr2O3 grain microstructure and increased spallation was observed for the alloys with large elongated grain microstructures (aspect ratio of 10 +/- 3).
引用
收藏
页数：21
相关论文
共 50 条
  • [1] Reduction in mechanical anisotropy through high temperature heat treatment of Hastelloy X processed by Selective Laser Melting (SLM)
    Etter, T.
    Kunze, K.
    Geiger, F.
    Meidani, H.
    17TH INTERNATIONAL CONFERENCE ON TEXTURES OF MATERIALS (ICOTOM 17), 2015, 82
  • [2] Comparison of wear behavior of GCr15 bearing steel prepared by selective laser melting (SLM) and electron beam melting (EBM)
    Li, Yunzhe
    Liu, Shifeng
    Xue, Tong
    Wei, Yingkang
    Yang, Xin
    Wang, Yan
    MATERIALS LETTERS, 2021, 305
  • [3] Microstructure and mechanical properties of Hastelloy X produced by HP-SLM (high power selective laser melting)
    Montero-Sistiaga, Maria L.
    Pourbabak, Saeid
    Van Humbeeck, Jan
    Schryvers, Dominique
    Vanmeensel, Kim
    MATERIALS & DESIGN, 2019, 165
  • [4] Effect of laser inclination angle on mechanical properties of Hastelloy X processed by selective laser melting
    Zong Xuewen
    Zhang Jian
    Fu Hanguang
    MATERIALS TESTING, 2021, 63 (01) : 10 - 16
  • [5] Effect of laser inclination angle on mechanical properties of Hastelloy X processed by selective laser melting
    Xuewen, Zong
    Jian, Zhang
    Hanguang, Fu
    Materialpruefung/Materials Testing, 2021, 63 (01): : 10 - 16
  • [6] High temperature oxidation of IN 718 manufactured by laser beam melting and electron beam melting: Effect of surface topography
    Sanviemvongsak, Tom
    Monceau, Daniel
    Macquaire, Bruno
    CORROSION SCIENCE, 2018, 141 : 127 - 145
  • [7] High Temperature Oxidation Behavior of Selective Laser Melting Manufactured IN 625
    Condruz, Mihaela Raluca
    Matache, Gheorghe
    Paraschiv, Alexandru
    Badea, Teodor
    Badilita, Viorel
    METALS, 2020, 10 (05)
  • [8] High temperature material properties of IN738LC processed by selective laser melting (SLM) technology
    Rickenbacher, L.
    Etter, T.
    Hoevel, S.
    Wegener, K.
    RAPID PROTOTYPING JOURNAL, 2013, 19 (04) : 282 - 290
  • [9] Comparative study of fatigue properties of Ti-6Al-4V specimens built by electron beam melting (EBM) and selective laser melting (SLM)
    Chastand, Victor
    Quaegebeur, Philippe
    Maia, Wilson
    Charkaluk, Eric
    MATERIALS CHARACTERIZATION, 2018, 143 : 76 - 81
  • [10] Directionally-Dependent Mechanical Properties of Ti6Al4V Manufactured by Electron Beam Melting (EBM) and Selective Laser Melting (SLM)
    Pasang, Tim
    Tavlovich, Benny
    Yannay, Omri
    Jackson, Ben
    Fry, Mike
    Tao, Yuan
    Turangi, Celine
    Wang, Jia-Chang
    Jiang, Cho-Pei
    Sato, Yuji
    Tsukamoto, Masahiro
    Misiolek, Wojciech Z.
    MATERIALS, 2021, 14 (13)
12345