Influence of thermal cycling treatment on the anneal hardening effect of Cu-10Zn Alloy

被引：10

作者：

Nestorovic, Svetlana ^{[1
]}

Markovic, Desimir ^{[1
]}

Markovic, Ivana ^{[1
]}

机构：

[1] Univ Belgrade, Tech Fac Bor, Bor 19210, Serbia

来源：

JOURNAL OF ALLOYS AND COMPOUNDS | 2010年 / 489卷 / 02期

关键词：

Copper alloy; Quenching; Anneal hardening effect; Thermal cycling treatment; Hardness measurements; SINTERED COPPER-ALLOYS; CU-TE ALLOYS; ELECTRICAL-CONDUCTIVITY; MECHANICAL PROPERTY; TEMPERATURE; MICROSTRUCTURE; BEHAVIOR; KINETICS;

D O I：

10.1016/j.jallcom.2009.09.115

中图分类号：

O64 [物理化学（理论化学）、化学物理学];

学科分类号：

070304 ; 081704 ;

摘要：

This paper reports the results of investigations on the influence of the so called thermal cycling treatment on the anneal hardening effect of the copper-based Cu-10at.% Zn alloy. The quenched samples were subjected to cold rolling of 20, 40 and 60% in reduction, followed by annealing with and without thermocycling treatment below the recrystallization temperature. Anneal hardening effect was observed in both samples in the temperature range between 180 and 300 degrees C and was followed by an increase in the hardness and electrical conductivity. These investigations showed that the thermal cycling treatment some increased the intensity of anneal hardening effect. (C) 2009 Elsevier B.V. All rights reserved.

引用

页码：582 / 585

页数：4

共 20 条

[1] MECHANISMS OF ANNEAL HARDENING IN CU-AL ALLOYS
BADER, M
ELDIS, GT
WARLIMONT, H
[J]. METALLURGICAL TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1976, 7 (02): : 249 - 255
[2] FEDOKIN VK, 1989, TERMOCIKLICESKAJA OB
[3] Microstructural and mechanical behavior of highly deformed Al-Sn alloys
Hernandez, O.
Gonzalez, G.
[J]. MATERIALS CHARACTERIZATION, 2008, 59 (05) : 534 - 541
[4] Thermal cycling of Ti46Al8Nb1B
Jiang, H.
Rong, T. S.
Hu, D.
Jones, I. P.
Voice, W.
[J]. INTERMETALLICS, 2006, 14 (12) : 1433 - 1447
[5] A high strength and high conductivity copper alloy prepared by spray forming
Li, ZY
Shen, J
Cao, FY
Li, QC
[J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2003, 137 (1-3) : 60 - 64
[6] Microstructure and mechanical properties of Cu-Ni-Si alloys
Monzen, Ryoichi
Watanabe, Chihiro
[J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2008, 483-84 : 117 - 119
[7] Influence of alloying and secondary annealing on anneal hardening effect at sintered copper alloys
Nestorovic, S
[J]. BULLETIN OF MATERIALS SCIENCE, 2005, 28 (05) : 401 - 403
[8] Influence of alloying on the anneal hardening effect in sintered copper alloys
Nestorovic, S
Markovic, D
[J]. MATERIALS TRANSACTIONS JIM, 1999, 40 (03): : 222 - 224
[9] Nestorovic S., 2002, Science of Sintering, V34, P169, DOI 10.2298/SOS0202169N
[10] Influence of degree of deformation in rolling on anneal hardening effect of a cast copper alloy
Nestorovic, S
Markovic, D
Ivanic, L
[J]. BULLETIN OF MATERIALS SCIENCE, 2003, 26 (06) : 601 - 604

← 1 2 →