The Investigation of Thrust Force of Printed Circuit Board Drilling

被引：8
|
作者：
Zheng, Lijuan [1 ]
Wang, Chengyong [1 ]
Qu, Yunpeng [1 ]
Yang, Lipeng [1 ]
Song, Yuexian [1 ]
机构：
[1] Guangdong Univ Technol, Guangzhou 510006, Guangdong, Peoples R China
来源：
PRECISION MACHINING VI | 2012年 / 496卷
关键词：
Drilling; PCB; Thrust force;
D O I：
10.4028/www.scientific.net/KEM.496.259
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
This work is focused on the investigation of the influence of the materials of PCB, feed rate, spindle speed and tool wear on thrust force when drilling PCB using 0.3 mm diameter cemented tungsten carbide drills. The results indicate that thrust force increases with feed rate and drill wear, but decreases with spindle speed firstly and then increases with it within the cutting range tested. Thrust force caused by the copper foil is much larger than that caused by the epoxy glass fiber cloth when feed rate is low. However, the difference between them decreases as feed rate increases. The thickness of nail head increases with thrust force. The accuracy of hole location increases with thrust force firstly but decreases afterward. The influence of thrust force on hole wall roughness is not obvious.
引用
收藏
页码：259 / 265
页数：7
相关论文
共 50 条
  • [41] Effects of Cutting Parameters and Point Angle on Thrust Force and Delamination in Drilling of CFRP
    Yardimeden, Ahmet
    Kilickap, Erol
    Celik, Yahya Hisman
    MATERIALS TESTING, 2014, 56 (11-12) : 1042 - 1048
  • [42] Analysis of thrust force and delamination in drilling GFRP composites with candle stick drills
    Liu, Liping
    Qi, Chunliang
    Wu, Feng
    Zhang, Xiaofeng
    Zhu, Xueming
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2018, 95 (5-8) : 2585 - 2600
  • [43] Effect of workpiece stiffness on thrust force and delamination in drilling thin composite laminates
    Luo, Bin
    Li, Yuan
    Zhang, Kaifu
    Cheng, Hui
    Liu, Shunuan
    JOURNAL OF COMPOSITE MATERIALS, 2016, 50 (05) : 617 - 625
  • [44] Experimental study of thrust force and surface quality when drilling hybrid stacks
    Mandi, Amani
    Turki, Yosra
    Habak, Malek
    Salem, Mehdi
    Bouaziz, Zoubeir
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2020, 107 (9-10) : 3981 - 3994
  • [45] Experimental study of thrust force and surface quality when drilling hybrid stacks
    Amani Mahdi
    Yosra Turki
    Malek Habak
    Mehdi Salem
    Zoubeir Bouaziz
    The International Journal of Advanced Manufacturing Technology, 2020, 107 : 3981 - 3994
  • [46] Analysis of thrust force and delamination in drilling GFRP composites with candle stick drills
    Liping Liu
    Chunliang Qi
    Feng Wu
    Xiaofeng Zhang
    Xueming Zhu
    The International Journal of Advanced Manufacturing Technology, 2018, 95 : 2585 - 2600
  • [47] Experimental investigation and analysis of factors influencing delamination and thrust force during drilling of carbon-fibre reinforced polymer composites
    Rajkumar, D.
    Ranjithkumar, P.
    Jenarthanan, M. P.
    Narayanan, Sathiya C.
    PIGMENT & RESIN TECHNOLOGY, 2017, 46 (06) : 507 - 524
  • [48] Modelling and Optimization for Thrust Force, Temperature and Burr Height in Drilling of Custom 450
    Gokce, H.
    EXPERIMENTAL TECHNIQUES, 2022, 46 (04) : 707 - 721
  • [49] Investigation of Thrust Force, Drill Bit Temperature and Burr Height in the Drilling of Aluminum Alloy Used in Ammunition Wing Drive Systems
    Gokce, H.
    Biberci, M. A.
    EXPERIMENTAL TECHNIQUES, 2022, 46 (04) : 691 - 705
  • [50] Investigation of Thrust Force, Drill Bit Temperature and Burr Height in the Drilling of Aluminum Alloy Used in Ammunition Wing Drive Systems
    H. Gökçe
    M. A. Biberci
    Experimental Techniques, 2022, 46 : 691 - 705
12345