Microstructure and properties of a novel wear- and corrosion-resistant stainless steel fabricated by laser melting deposition

被引：13
|
作者：
Han, Yurou [1 ]
Zhang, Chunhua [1 ]
Cui, Xue [1 ]
Zhang, Song [1 ]
Chen, Jiang [2 ]
Dong, Shiyun [3 ]
Abdullah, Adil Othman [4 ]
机构：
[1] Shenyang Univ Technol, Sch Mat Sci & Engn, Shenyang 110870, Liaoning, Peoples R China
[2] Shenyang Dalu Laser Technol Co Ltd, Shenyang 110136, Liaoning, Peoples R China
[3] Army Acad Armored Forces, Nat Key Lab Remfg, Beijing 100072, Peoples R China
[4] China Med Univ, Sch & Hosp Stomatol, Stomatol Res Ctr, Shenyang 110002, Liaoning, Peoples R China
来源：
JOURNAL OF MATERIALS RESEARCH | 2020年 / 35卷 / 15期
关键词：
laser melting deposition; stainless steel; microhardness; wear resistance; corrosion resistance; MECHANICAL-PROPERTIES; NI CONTENT; ALLOY; BEHAVIOR; 304-STAINLESS-STEEL; TEMPERATURE; EVOLUTION; MODEL; CR;
D O I：
10.1557/jmr.2020.70
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
The study investigated novel wear and corrosion resistance of stainless steel and 316 stainless steel samples which were successfully prepared by laser melting deposition. Phase composition, microstructure, microhardness, wear resistance, and electrochemical corrosion resistance were studied. The experimental results showed that novel stainless steel was mainly composed of alpha-Fe and a few carbide phase (Cr, Fe)(7)C-3. The microhardness of novel stainless steel was about 2.7 times greater than 316 stainless steel. Meanwhile, the specific wear rate of novel stainless steel and 316 stainless steel was 2.63 x 10(-5) mm(3)/N m and 1.63 x 10(-4) mm(3)/N m, respectively. The wear volume of 316 stainless steel was 6.19 times greater than novel stainless steel. The corrosion current and the corrosion potential of novel stainless steel and 316 stainless steel were 1.02 x 10(-7) A/cm(2) and 1.5 x 10(-7) A/cm(2), and -138.8 mV, -135.9 mV, respectively, in 3.5 wt% NaCl solution. Therefore, both microhardness and wear resistance of novel stainless steel were greatly improved, with high corrosion resistance.
引用
收藏
页码：2006 / 2015
页数：10
相关论文
共 50 条
  • [21] Microstructure and Anisotropy of the Mechanical Properties of 316L Stainless Steel Fabricated by Selective Laser Melting
    Zhou, Baogang
    Xu, Pingwei
    Li, Wei
    Liang, Yilong
    Liang, Yu
    METALS, 2021, 11 (05)
  • [22] Microstructure and mechanical properties of TiB2-reinforced 7075 aluminum matrix composites fabricated by laser melting deposition
    Bi Jiang
    Lei Zhenglong
    Chen Xi
    Li Peng
    Lu Nannan
    Chen Yanbin
    CERAMICS INTERNATIONAL, 2019, 45 (05) : 5680 - 5692
  • [23] Composition Design, Microstructures and Properties of Fe-Based Wear- and Corrosion- Resistant Coatings by Laser Cladding
    Ye, Jieliang
    Feng, Yueqiao
    Li, Zhuguo
    Zhang, Xunguo
    CHINESE JOURNAL OF LASERS-ZHONGGUO JIGUANG, 2023, 50 (10):
  • [24] Tungsten particle-reinforced 316L steel fabricated by laser melting deposition: Microstructure and mechanical properties
    Sun, Yiping
    Wang, Bin
    Ren, Yongpeng
    Li, Chunlei
    Lei, Jianbo
    Zhang, Songpeng
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2025, 929
  • [25] Duplex stainless steel fabricated by selective laser melting - Microstructural and mechanical properties
    Hengsbach, Florian
    Koppa, Peter
    Duschik, Kristina
    Holzweissig, Martin Joachim
    Burns, Madison
    Nellesen, Jens
    Tillmann, Wolfgang
    Troester, Thomas
    Hoyer, Kay-Peter
    Schaper, Mirko
    MATERIALS & DESIGN, 2017, 133 : 136 - 142
  • [26] Effect of In-Situ Ti2N on Microstructure and Properties of SAF2906 Duplex Stainless Steel Fabricated by Laser Melting Deposition
    Liang, Jing
    Yang, Sheng
    Liu, Ye
    Yin, Xiuyuan
    Chen, Suiyuan
    Liu, Changsheng
    METALS AND MATERIALS INTERNATIONAL, 2023, 29 (07) : 2052 - 2071
  • [27] The research of wear and corrosion-resistant properties of laser coatings with strengthening phase
    Cherepanov, Anatoly N.
    Malikov, Alexander G.
    Orishich, Anatoly M.
    Drozdov, Vladimir O.
    NAUKA I TEHNOLOGII TRUBOPROVODNOGO TRANSPORTA NEFTI I NEFTEPRODUKTOV-SCIENCE & TECHNOLOGIES-OIL AND OIL PRODUCTS PIPELINE TRANSPORTATION, 2020, 10 (03): : 305 - 313
  • [28] Characterisation of heat-treated gradient alloy steel fabricated by laser melting deposition
    Liang, X. D.
    Zhang, S.
    Wang, Z. Y.
    Zhang, C. H.
    Zhang, D. X.
    Wu, C. L.
    MATERIALS SCIENCE AND TECHNOLOGY, 2023, 39 (05) : 567 - 581
  • [29] Effect of selective laser melting process parameters on the microstructure and properties of a precipitation hardening stainless steel
    Fang, Ruirui
    Deng, Nana
    Zhang, Hongbin
    Wang, Gang
    Su, Yukuo
    Zhou, Haiping
    Gao, Kuidong
    Gu, Lianwang
    MATERIALS & DESIGN, 2021, 212
  • [30] Microstructure and mechanical properties of stainless steel/calcium silicate composites manufactured by selective laser melting
    Zheng, Zeng
    Wang, Lianfeng
    Jia, Min
    Cheng, Lingyu
    Yan, Biao
    MATERIALS SCIENCE & ENGINEERING C-MATERIALS FOR BIOLOGICAL APPLICATIONS, 2017, 71 : 1099 - 1105
12345