Nanoindentation and Wear Characteristics of Al 5083/SiCp Nanocomposites Synthesized by High Energy Ball Milling and Spark Plasma Sintering

被引：32

作者：

Bathula, Sivaiah ^{[1
]}

Saravanan, M. ^{[1
]}

Dhar, Ajay ^{[1
]}

机构：

[1] CSIR, Natl Phys Lab, Met & Alloys Grp, Mat Phys & Engn Div, New Delhi 110012, India

来源：

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY | 2012年 / 28卷 / 11期

关键词：

Metal matrix nano composites; Friction/wear; Mechanical properties; High resolution transmission electron microscopy; Spark plasma sintering; Nanoindentation; DRY SLIDING WEAR; REINFORCED ALUMINUM; COMPOSITES; BEHAVIOR; POWDER; HARDNESS; SIZE;

D O I：

10.1016/S1005-0302(12)60160-1

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Al 5083/10 wt% SiCp nano composites have been synthesized by means of high energy ball milling followed by spark plasma sintering (SPS). Nano composites produced via this method exhibited near-theoretical density while retaining the nano-grained features. X-ray diffraction (XRD) analysis indicated that the crystalline size of the ball milled Al 5083 matrix was observed to be similar to 25 nm and it was coarsened up to similar to 30 nm after SPS. Nano indentation results of nano composites demonstrated a high hardness of similar to 280 HV with an elastic modulus of 126 GPa. Wear and friction characteristics with addition of SiCp reinforcement exhibited significant improvement in terms of coefficient of friction and specific wear rate to that of nano structured Al 5083 alloy. The reduction in specific wear rate in the nanocomposite was mainly due to the change of wear mechanism from adhesive to abrasive wear with the addition of SiCp which resulted in high hardness associated with nano-grained microstructure.

引用

页码：969 / 975

页数：7

共 30 条

[1] Wear Behavior of Nanostructured Al and Al-B4C Nanocomposites Produced by Mechanical Milling and Hot Extrusion [J].

Alizadeh, A. ;

Taheri-Nassaj, E. .

TRIBOLOGY LETTERS, 2011, 44 (01) :59-66

[2] Microstructural features and mechanical properties of Al 5083/SiCp metal matrix nanocomposites produced by high energy ball milling and spark plasma sintering [J].

Bathula, Sivaiah ;

Anandani, R. C. ;

Dhar, Ajay ;

Srivastava, A. K. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2012, 545 :97-102

[3] About the epitaxial growth of Mg-subgrains on Al2MgC2 interfacial carbides in a squeeze cast Mg-4Al/T300 metal matrix composite [J].

Cayron, C ;

Buffat, PA ;

Hausmann, C ;

Beffort, O .

JOURNAL OF MATERIALS SCIENCE LETTERS, 1999, 18 (20) :1671-1674

[4] Interface Structure of Ag/SnO2 Nanocomposite Fabricated by Reactive Synthesis [J].

Chen, Jingchao ;

Feng, Jing ;

Xiao, B. ;

Zhang, K. H. ;

Du, Y. P. ;

Hong, Z. J. ;

Zhou, R. .

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2010, 26 (01) :49-55

[5] Aluminium-matrix silicon carbide whisker composites fabricated by pressureless infiltration [J].

Chen, YY ;

Chung, DDL .

JOURNAL OF MATERIALS SCIENCE, 1996, 31 (02) :407-412

[6]

Cullity BD, 2001, Elements of X-ray Diffraction

[7] The studies of crystallite size and microstrains in aluminum powder prepared by mechanical milling [J].

Daly, R. ;

Khitouni, M. ;

Kolsi, A. W. ;

Njah, N. .

PHYSICA STATUS SOLIDI C - CURRENT TOPICS IN SOLID STATE PHYSICS, VOL 3, NO 9, 2006, 3 (09) :3325-+

[8]

Davis J., 2002, ASM Specialty Handbook: Aluminum and Aluminum Alloys

[9] Dry sliding wear of aluminium composites - A review [J].

Deuis, RL ;

Subramanian, C ;

Yellup, JM .

COMPOSITES SCIENCE AND TECHNOLOGY, 1997, 57 (04) :415-435

[10]

Dhar A., 2012, ADV MAT RES, V410, P224

← 1 2 3 →