Dual-rotor tool path generation and removal error analysis in active feed polishing

被引:8
作者
Wang, Shaozhi [1 ]
Liu, Jian [1 ]
Zhang, Linghua [1 ]
机构
[1] Chinese Acad Sci, Changchun Inst Opt Fine Mech & Phys, State Key Lab Appl Opt, Changchun 130033, Peoples R China
关键词
OPTIMIZATION;
D O I
10.1364/AO.52.006948
中图分类号
O43 [光学];
学科分类号
070207 ; 0803 ;
摘要
High-quality ultrasmooth surface is needed in modern optics, while the existing ultrasmooth surface processing methods are difficult to meet the requirement of the surface figure. In order to solve this problem, the active feed polishing (AFP) is taken as the research object, and the dual-rotor tool path is put forward for this technology. This tool path is generated based on the motion synthesis principle, which realizes smooth connection between different sections. At the same time, the eccentricity, the speed ratio, the velocity, and other parameters can be modified easily, avoiding using the complicated dual-rotor polishing mechanism. In order to further analyze the removal error, the removal amount calculation method for the dual-rotor path is researched and proposed. The simulation analysis results show that the greatest influence factor for the removal error is the sampling interval, the influence of the eccentricity and the speed ratio is less, and the velocity has little impact on it. In addition, the removal error can be controlled within acceptable range by reasonable selection of process parameters. Finally, through a processing experiment of a 100 mm plane lens, the feasibility and effectiveness of this path is verified. This experimental result shows that the AFP technology using the dual-rotor tool path can effectively correct the surface shape while reducing the surface roughness. (C) 2013 Optical Society of America
引用
收藏
页码:6948 / 6955
页数:8
相关论文
共 24 条
[1]   FLOAT POLISHING OF OPTICAL-MATERIALS [J].
BENNETT, JM ;
SHAFFER, JJ ;
SHIBANO, Y ;
NAMBA, Y .
APPLIED OPTICS, 1987, 26 (04) :696-703
[2]  
Bollinger L. D., 1991, P SOC PHOTO-OPT INS, V1618, P14
[3]   Optimization of Removal Function in Computer Controlled Optical Surfacing [J].
Chen Xi ;
Guo Peiji ;
Ren Jianfeng .
5TH INTERNATIONAL SYMPOSIUM ON ADVANCED OPTICAL MANUFACTURING AND TESTING TECHNOLOGIES: ADVANCED OPTICAL MANUFACTURING TECHNOLOGIES, 2010, 7655
[4]   Characterization of wet pad surface in chemical mechanical polishing (CMP) process with full-field optical coherence tomography (FF-OCT) [J].
Choi, Woo June ;
Jung, Sung Pyo ;
Shin, Jun Geun ;
Yang, Danning ;
Lee, Byeong Ha .
OPTICS EXPRESS, 2011, 19 (14) :13343-13350
[5]  
Dai Yi-fan, 2006, Journal of National University of Defense Technology, V28, P97
[6]  
Gao H., 1995, ACTA OPT SINICA, V15, P824
[7]  
JOHNSON JR, 1990, P SOC PHOTO-OPT INS, V1333, P106, DOI 10.1117/12.22793
[8]  
Jones R. A., 1979, Proceedings of the Society of Photo-Optical Instrumentation Engineers, vol.171. Optical Components: Manufacture and Evaluation, P102
[9]   FABRICATION USING COMPUTER-CONTROLLED POLISHER [J].
JONES, RA .
APPLIED OPTICS, 1978, 17 (12) :1889-1892
[10]   COMPUTER-CONTROLLED POLISHING OF TELESCOPE MIRROR SEGMENTS [J].
JONES, RA .
OPTICAL ENGINEERING, 1983, 22 (02) :236-240