Effect of strain rate on stress-induced martensitic formation and the compressive properties of Ti-V-(Cr,Fe)-Al alloys

被引：39
作者：
Li, C. [1 ,2 ]
Chen, J. H. [1 ]
Wu, X. [2 ]
van der Zwaag, S. [2 ]
机构：
[1] Hunan Univ, Coll Mat Sci & Engn, Changsha 410082, Hunan, Peoples R China
[2] Delft Univ Technol, Fac Aerosp Engn, NL-2629 HS Delft, Netherlands
来源：
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2013年 / 573卷
基金：
中国国家自然科学基金;
关键词：
Titanium alloys; Strain rate; Triggering stress; Compressive properties; DEFORMATION-INDUCED MARTENSITE; TRIGGER STRESS; TENSILE PROPERTIES; TITANIUM-ALLOYS; VOLUME FRACTION; PHASE-STABILITY; BETA; TRANSFORMATION; NB; AL;
D O I：
10.1016/j.msea.2013.03.002
中图分类号：
TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
The effect of strain rate on the stress required to trigger stress-induced martensitic (SIM) transformation and the compressive properties of three titanium alloys (Ti-10V-2Fe-3Al, Ti-10V-2Cr-3Al, Ti-10V-1Fe3Al) has been investigated for strain rates ranging from 1x10(-1) s(-1) to 1x10(-4) s(-1). The heat treated grades exhibited SIM transformation at all the strain rates applied. I was found that the triggering stress for SIM transformation (yield stress) and failure strain increased continuously with increasing strain rate. The compression strength was found to increase first and then to decrease with increasing strain rate. Grades not showing the SIM effect showed similar trends except in their compression strength. (C) 2013 Elsevier B.V. All rights reserved.
引用
收藏
页码：111 / 118
页数：8
相关论文
共 39 条
[1]   Effect of βgrain size on stress induced martensitic transformation in βsolution treated Ti-10V-2Fe-W alloy [J].
Bhattacharjee, A ;
Bhargava, S ;
Varma, VK ;
Kamat, SV ;
Gogia, AK .
SCRIPTA MATERIALIA, 2005, 53 (02) :195-200
[2]  
Bong W., 2007, J UNIV SCI TECHNOL B, P335
[3]   PHASE-TRANSFORMATIONS AND TENSILE PROPERTIES OF TI-10V-2FE-3AL [J].
DUERIG, TW ;
TERLINDE, GT ;
WILLIAMS, JC .
METALLURGICAL TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1980, 11 (12) :1987-1998
[4]   Strengthening of α+β titanium alloys by thermomechanical processing [J].
Fujii, H .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1998, 243 (1-2) :103-108
[5]   The effect of cooling rate on the cyclic deformation of β-annealed Ti-6Al-4V [J].
Gil, FJ ;
Manero, JM ;
Ginebra, MP ;
Planell, JA .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2003, 349 (1-2) :150-155
[6]   Deformation induced martensite and superelasticity in a β-metastable titanium alloy [J].
Grosdidier, T ;
Philippe, MJ .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2000, 291 (1-2) :218-223
[7]   Structure/deformation relationship in a beta metastable Ti-alloy [J].
Grosdidier, T ;
Roubaud, C ;
Philippe, MJ ;
Zaefferer, S ;
Zandona, M ;
Gautier, E ;
Combres, Y .
JOURNAL DE PHYSIQUE IV, 1996, 6 (C1) :435-444
[8]   Effect of microstructure variations on the formation of deformation-induced martensite and associated tensile properties in a β metastable Ti alloy [J].
Grosdidier, T ;
Combres, Y ;
Gautier, E ;
Philippe, MJ .
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2000, 31 (04) :1095-1106
[9]   KINETICS OF MARTENSITIC INTERFACE MOTION [J].
GRUJICIC, M ;
OLSON, GB ;
OWEN, WS .
JOURNAL DE PHYSIQUE, 1982, 43 (NC-4) :173-178
[10]   MOBILITY OF MARTENSITIC INTERFACES [J].
GRUJICIC, M ;
OLSON, GB ;
OWEN, WS .
METALLURGICAL TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1985, 16 (10) :1713-1722
1234