Evaluation of heat transfer at the cavity-polymer interface in microinjection moulding based on experimental and simulation study
被引:29
作者:
Babenko, Maksims
论文数: 0引用数: 0
h-index: 0
机构:
Univ Bradford, Sch Engn, Fac Engn & Informat, Ctr Polymer Micro & Nano Technol, Bradford, W Yorkshire, EnglandUniv Bradford, Sch Engn, Fac Engn & Informat, Ctr Polymer Micro & Nano Technol, Bradford, W Yorkshire, England
Babenko, Maksims
[1
]
Sweeney, John
论文数: 0引用数: 0
h-index: 0
机构:
Univ Bradford, Sch Engn, Fac Engn & Informat, Ctr Polymer Micro & Nano Technol, Bradford, W Yorkshire, EnglandUniv Bradford, Sch Engn, Fac Engn & Informat, Ctr Polymer Micro & Nano Technol, Bradford, W Yorkshire, England
Sweeney, John
[1
]
Petkov, Petko
论文数: 0引用数: 0
h-index: 0
机构:
Cardiff Univ, Cardiff Sch Engn, High Value Mfg Res Grp, Cardiff, S Glam, WalesUniv Bradford, Sch Engn, Fac Engn & Informat, Ctr Polymer Micro & Nano Technol, Bradford, W Yorkshire, England
Petkov, Petko
[2
]
Lacan, Franck
论文数: 0引用数: 0
h-index: 0
机构:
Cardiff Univ, Cardiff Sch Engn, High Value Mfg Res Grp, Cardiff, S Glam, WalesUniv Bradford, Sch Engn, Fac Engn & Informat, Ctr Polymer Micro & Nano Technol, Bradford, W Yorkshire, England
Lacan, Franck
[2
]
Bigot, Samuel
论文数: 0引用数: 0
h-index: 0
机构:
Cardiff Univ, Cardiff Sch Engn, High Value Mfg Res Grp, Cardiff, S Glam, WalesUniv Bradford, Sch Engn, Fac Engn & Informat, Ctr Polymer Micro & Nano Technol, Bradford, W Yorkshire, England
Bigot, Samuel
[2
]
Whiteside, Ben
论文数: 0引用数: 0
h-index: 0
机构:
Univ Bradford, Sch Engn, Fac Engn & Informat, Ctr Polymer Micro & Nano Technol, Bradford, W Yorkshire, EnglandUniv Bradford, Sch Engn, Fac Engn & Informat, Ctr Polymer Micro & Nano Technol, Bradford, W Yorkshire, England
Whiteside, Ben
[1
]
机构:
[1] Univ Bradford, Sch Engn, Fac Engn & Informat, Ctr Polymer Micro & Nano Technol, Bradford, W Yorkshire, England
[2] Cardiff Univ, Cardiff Sch Engn, High Value Mfg Res Grp, Cardiff, S Glam, Wales
In polymer melt processing, the heat transfer coefficient (HTC) determines the heat flux across the interface of the polymer melt and the mould wall. The HTC is a dominant parameter in cooling simulations especially for microinjection moulding, where the high surface to volume ratio of the part results in very rapid cooling. Moreover, the cooling rate can have a significant influence on internal structure, morphology and resulting physical properties. HTC values are therefore important and yet are not well quantified. To measure HTC in micromoulding, we have developed an experimental setup consisting of a special mould, and an ultra-high speed thermal camera in combination with a range of windows. The windows were laser machined on their inside surfaces to produce a range of surface topographies. Cooling curves were obtained for two materials at different processing conditions, the processing variables explored being melt and mould temperature, injection speed, packing pressure and surface topography. The finite element package Moldflow was used to simulate the experiments and to find the HTC values that best fitted the cooling curves, so that HTC is known as a function of the process variables explored. These results are presented and statistically analysed. An increase in HTC from the standard value of 2500 W/m(2) C to values in the region 7700 W/m(2) C was required to accurately model the observations. (C) 2017 The Authors. Published by Elsevier Ltd. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/).
机构:
Korea Inst Ind Technol, Molds & Dies Technol R&BD Grp, Bucheon Si, Gyeonggi Do, South Korea
Dankook Univ, Dept Mech Engn, Bucheon Si, Gyeonggi Do, South KoreaKorea Inst Ind Technol, Molds & Dies Technol R&BD Grp, Bucheon Si, Gyeonggi Do, South Korea
Hong, Seokkwan
Kang, Jeongjin
论文数: 0引用数: 0
h-index: 0
机构:
Korea Inst Ind Technol, Molds & Dies Technol R&BD Grp, Bucheon Si, Gyeonggi Do, South KoreaKorea Inst Ind Technol, Molds & Dies Technol R&BD Grp, Bucheon Si, Gyeonggi Do, South Korea
Kang, Jeongjin
Yoon, Kyunghwan
论文数: 0引用数: 0
h-index: 0
机构:
Dankook Univ, Dept Mech Engn, Bucheon Si, Gyeonggi Do, South KoreaKorea Inst Ind Technol, Molds & Dies Technol R&BD Grp, Bucheon Si, Gyeonggi Do, South Korea
机构:
Korea Inst Ind Technol, Molds & Dies Technol R&BD Grp, Bucheon Si, Gyeonggi Do, South Korea
Dankook Univ, Dept Mech Engn, Bucheon Si, Gyeonggi Do, South KoreaKorea Inst Ind Technol, Molds & Dies Technol R&BD Grp, Bucheon Si, Gyeonggi Do, South Korea
Hong, Seokkwan
Kang, Jeongjin
论文数: 0引用数: 0
h-index: 0
机构:
Korea Inst Ind Technol, Molds & Dies Technol R&BD Grp, Bucheon Si, Gyeonggi Do, South KoreaKorea Inst Ind Technol, Molds & Dies Technol R&BD Grp, Bucheon Si, Gyeonggi Do, South Korea
Kang, Jeongjin
Yoon, Kyunghwan
论文数: 0引用数: 0
h-index: 0
机构:
Dankook Univ, Dept Mech Engn, Bucheon Si, Gyeonggi Do, South KoreaKorea Inst Ind Technol, Molds & Dies Technol R&BD Grp, Bucheon Si, Gyeonggi Do, South Korea