Fluid flow and heat transfer in an air-to-water double-pipe heat exchanger

被引：16

作者：

Sheikholeslami, M. ^{[1
]}

Gorji-Bandpy, M. ^{[1
]}

Ganji, D. D. ^{[1
]}

机构：

[1] Babol Univ Technol, Dept Mech Engn, Babol Sar, Iran

来源：

EUROPEAN PHYSICAL JOURNAL PLUS | 2015年 / 130卷 / 11期

关键词：

TRANSFER ENHANCEMENT; PERFORMANCE EVALUATION; CIRCULAR TUBE; NANOFLUIDS;

D O I：

10.1140/epjp/i2015-15225-y

中图分类号：

O4 [物理学];

学科分类号：

0702 ;

摘要：

This paper reports experimental and numerical investigations on flow and heat transfer in an air-to-water double-pipe heat exchanger. The working fluids are air and water. To achieve fully developed conditions, the heat exchanger was built with additional lengths before and after the test section. The inner and outer tube was made from copper and Plexiglas, respectively. The experiments are conducted in the range of air flow Reynolds number for various cases with different water flow rate and water inlet temperature. Correlations for the Nusselt number and friction factor are presented according to experimental data. Also the commercial code ANSYS 15 is used for numerical simulation. Results show that the Nusselt number is an increasing function of Reynolds number and Prandtl number which are calculated at bulk temperature.

引用

页码：1 / 12

页数：12

共 22 条

[1]

[Anonymous], 2006, Introduction to Heat Transfer

[2] Performance assessment in a heat exchanger tube fitted with double counter twisted tape inserts [J].

Bhuiya, M. M. K. ;

Sayem, A. S. M. ;

Islam, M. ;

Chowdhury, M. S. U. ;

Shahabuddin, M. .

INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER, 2014, 50 :25-33

[3] Thermal performance of tubular heat exchanger with multiple twisted-tape inserts [J].

Chokphoemphun, Suriya ;

Pimsarn, Monsak ;

Thianpong, Chinaruk ;

Promvonge, Pongjet .

CHINESE JOURNAL OF CHEMICAL ENGINEERING, 2015, 23 (05) :755-762

[4] Impact of fluid-mover characteristics on heat exchanger performance: A new reality-based analysis approach [J].

Gorman, J. M. ;

Sparrow, E. M. ;

Minkowycz, W. J. .

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2015, 86 :581-588

[5] Optimization of finned-tube heat exchangers for diesel exhaust waste heat recovery using CFD and CCD techniques [J].

Hatami, M. ;

Jafaryar, M. ;

Ganji, D. D. ;

Gorji-Bandpy, M. .

INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER, 2014, 57 :254-263

[6] A review of different heat exchangers designs for increasing the diesel exhaust waste heat recovery [J].

Hatami, M. ;

Ganji, D. D. ;

Gorji-Bandpy, M. .

RENEWABLE & SUSTAINABLE ENERGY REVIEWS, 2014, 37 :168-181

[7] Heat transfer enhancement using nanofluids in an automotive cooling system [J].

Hussein, Adnan M. ;

Bakar, R. A. ;

Kadirgama, K. ;

Sharma, K. V. .

INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER, 2014, 53 :195-202

[8] Thermo-hydraulic performance of a heat exchanger tube with discrete corrugations [J].

Kathait, Pawan Singh ;

Patil, Anil Kumar .

APPLIED THERMAL ENGINEERING, 2014, 66 (1-2) :162-170

[9] Experimental study of nanofluid flow and heat transfer over microscale backward- and forward-facing steps [J].

Kherbeet, A. Sh. ;

Mohammed, H. A. ;

Salman, B. H. ;

Ahmed, Hamdi E. ;

Alawi, Omer A. ;

Rashidi, M. M. .

EXPERIMENTAL THERMAL AND FLUID SCIENCE, 2015, 65 :13-21

[10] Comprehensive performance evaluation and parametric studies of single pass solar air heater with fins and baffles attached over the absorber plate [J].

Mohammadi, K. ;

Sabzpooshani, M. .

ENERGY, 2013, 57 :741-750

← 1 2 3 →