Analysis of the hard turning of AISI H13 steel with ceramic tools based on tool geometry: surface roughness, tool wear and their relation

被引：32
作者：
Ferreira, R. [1 ]
Rehor, Jan [2 ]
Lauro, Carlos H. [1 ]
Carou, D. [1 ]
Davim, J. P. [1 ]
机构：
[1] Univ Aveiro, Dept Mech Engn, Campus Santiago, P-3810193 Aveiro, Portugal
[2] Univ West Bohemia, Reg Technol Inst, Plzen 30100, Czech Republic
来源：
JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING | 2016年 / 38卷 / 08期
关键词：
AISI H13 steel; Ceramic tools; Flank wear; Surface roughness; Wiper; CUTTING FORCE COMPONENTS; ALLOY-STEEL; WIPER; FINISH; OPTIMIZATION; PERFORMANCE; MACHINABILITY; INSERTS; D2; PARAMETERS;
D O I：
10.1007/s40430-016-0504-z
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
Nowadays, hard turning is one of the most important processes for both industry and researchers to substitute traditional grinding operations. The present study shows an experimental investigation on the turning of AISI H13 steel with ceramic tools: conventional and wiper. Wiper geometry has as main objective obtained a smoother surface after the cutting process. Turning tests were performed to evaluate the evolution of the surface roughness and tool wear; and the influence of the flank wear on the surface roughness. A slightly better performance of wiper tools was observed for the flank wear, while no clear trend was observed when analysing the surface roughness. In most of the cases, wiper tools provided better surface roughness than conventional tools but not for all the cases. In addition, the difference in the obtained results varied widely depending on the machining length. Finally, no clear relation was found between the flank wear and the surface roughness.
引用
收藏
页码：2413 / 2420
页数：8
相关论文
共 42 条
[11]   Comparative assessment of wiper and conventional ceramic tools on surface roughness in hard turning AISI 4140 steel [J].
Elbah, Mohamed ;
Yallese, Mohamed Athmane ;
Aouici, Hamdi ;
Mabrouki, Tarek ;
Rigal, Jean-Francois .
MEASUREMENT, 2013, 46 (09) :3041-3056
[12]   Surface roughness measurement in turning carbon steel AISI 1045 using wiper inserts [J].
Esteves Correia, A. ;
Paulo Davim, J. .
MEASUREMENT, 2011, 44 (05) :1000-1005
[13]   Surface Roughness Investigation in the Hard Turning of Steel Using Ceramic Tools [J].
Ferreira, R. ;
Carou, D. ;
Lauro, C. H. ;
Davim, J. P. .
MATERIALS AND MANUFACTURING PROCESSES, 2016, 31 (05) :648-652
[14]   Analysis of Machinability During Hard Turning of Cold Work Tool Steel (Type: AISI D2) [J].
Gaitonde, V. N. ;
Karnik, S. R. ;
Figueira, Luis ;
Davim, J. Paulo .
MATERIALS AND MANUFACTURING PROCESSES, 2009, 24 (12) :1373-1382
[15]   Machinability investigations in hard turning of AISI D2 cold work tool steel with conventional and wiper ceramic inserts [J].
Gaitonde, V. N. ;
Karnik, S. R. ;
Figueira, Luis ;
Davim, J. Paulo .
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS, 2009, 27 (04) :754-763
[16]   Performance comparison of conventional and wiper ceramic inserts in hard turning through artificial neural network modeling [J].
Gaitonde, Vinayak Neelakanth ;
Karnik, S. R. ;
Figueira, Luis ;
Davim, J. Paulo .
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2011, 52 (1-4) :101-114
[17]   Hard turning of tempered DIN 100Cr6 steel with coated and no coated CBN inserts [J].
Galoppi, Gustavo de Siqueira ;
Stipkovic Filho, Marco ;
Batalha, Gilmar Ferreira .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2006, 179 (1-3) :146-153
[18]   Wear phenomenon in the hard steel machining using ceramic tools [J].
Grzesik, W. ;
Zalisz, Z. .
TRIBOLOGY INTERNATIONAL, 2008, 41 (08) :802-812
[19]   Influence of tool wear on surface roughness in hard turning using differently shaped ceramic tools [J].
Grzesik, W. .
WEAR, 2008, 265 (3-4) :327-335
[20]   Surface finish generated in hard turning of quenched alloy steel parts using conventional and wiper ceramic inserts [J].
Grzesik, W. ;
Wanat, T. .
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2006, 46 (15) :1988-1995
12345