Influence of cooling rate on the precipitation microstructure in a medium strength Al-Zn-Mg alloy

被引：97

作者：

Deschamps, A. ^{[1
]}

Texier, G. ^{[1
,2
]}

Ringeval, S. ^{[1
,2
]}

Delfaut-Durut, L. ^{[2
]}

机构：

[1] INPGrenoble CNRS UJF, SIMAP, F-38402 St Martin Dheres, France

[2] CEA DAM Ctr Valduc, F-21120 Is Sur Tille, France

来源：

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2009年 / 501卷 / 1-2期

关键词：

Al-Zn-Mg alloy; Precipitation; Quench; Ageing; QUENCH FACTOR-ANALYSIS; ALUMINUM-ALLOYS; SENSITIVITY; TOUGHNESS; BEHAVIOR;

D O I：

10.1016/j.msea.2008.09.067

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

Medium strength Al-Zn-Mg age hardening alloys are widely used when a low quench sensitivity is required. such as in welding applications. In this work we present a detailed characterization of the precipitate microstructures resulting from different quench rates from the solution treatment, and from the subsequent artificial ageing to the T6 state, in an Al-4.5Zn-1 Mg (wt%) alloy. This work is carried out using differential scanning calorimetry, transmission electron microscopy and in situ small-angle X-ray scattering. It is shown that for quench rate between 5 and 200 degrees C/min substantial heterogeneous precipitation is observed, nucleated on dispersoids and on grain boundaries, the former being of much larger size than the latter. During subsequent ageing, it is shown that the precipitation kinetics in the material unaffected by the quench-induced precipitates is independent on the quench rate used. (c) 2008 Elsevier B.V. All rights reserved.

引用

页码：133 / 139

页数：7

共 20 条

[11]

FRENCH WA, 1978, WELD RES INT, V8, P1

[12] Precipitation sequences during quenching of the AA 7010 alloy [J].

Godard, D ;

Archambault, P ;

Aeby-Gautier, E ;

Lapasset, G .

ACTA MATERIALIA, 2002, 50 (09) :2319-2329

[13] Continuous cooling transformation (CCT) diagram of aluminum alloy Al-4.5Zn-1Mg [J].

Kessler, O. ;

von Bargen, R. ;

Hoffmann, F. ;

Zoch, H-W. .

ALUMINIUM ALLOYS 2006, PTS 1 AND 2: RESEARCH THROUGH INNOVATION AND TECHNOLOGY, 2006, 519-521 :1467-1472

[14] Precipitation and strengthening in aluminium alloys [J].

Lendvai, J .

ALUMINIUM ALLOYS: THEIR PHYSICAL AND MECHANICAL PROPERTIES, PTS 1-3, 1996, 217 :43-56

[15] Improved quench sensitivity in modified aluminum alloy 7175 for thick forging applications [J].

Lim, ST ;

Yun, SJ ;

Nam, SW .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2004, 371 (1-2) :82-90

[16] Influence of aging on quench sensitivity effect of 7055 aluminum alloy [J].

Liu, S. D. ;

Zhang, X. M. ;

Chen, M. A. ;

You, J. H. .

MATERIALS CHARACTERIZATION, 2008, 59 (01) :53-60

[17] Softening behaviour of Al-Zn-Mg alloys due to welding [J].

Ma, T ;

den Ouden, G .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1999, 266 (1-2) :198-204

[18] In situ thermal studies and post-weld mechanical properties of friction stir welds in age hardenable aluminium alloys [J].

Nelson, TW ;

Steel, RJ ;

Arbegast, WJ .

SCIENCE AND TECHNOLOGY OF WELDING AND JOINING, 2003, 8 (04) :283-288

[19]

STALEY JT, 1987, MATER SCI TECH SER, V3, P923, DOI 10.1179/026708387790220991

[20]

Staley JT, 2001, P MAT SOL C ASM INT, P6

← 1 2 →