EFFECT OF MARTENSITE DISTRIBUTION ON MICROSCOPIC DEFORMATION BEHAVIOR AND MECHANICAL PROPERTIES OF DUAL PHASE STEELS

被引:0
作者
Deng Jie [1 ]
Ma Jiawei [1 ]
Xu Yiyang [1 ]
Shen Yao [1 ]
机构
[1] Shanghai Jiao Tong Univ, State Key Lab Met Matrix Composites, Shanghai 200240, Peoples R China
关键词
dual phase steel; microstructure; plastic deformation; step quenching; intercritical annealing; digital image correlation (DIC); DIGITAL IMAGE CORRELATION; STRAIN; MORPHOLOGY; TENSILE; FERRITE;
D O I
暂无
中图分类号
TF [冶金工业];
学科分类号
0806 ;
摘要
Investigation of the relationship between microstructure and microscopic deformation behavior of dual phase steel is very important for high property dual phase steel development. In this work, step quenching (SQ) and intercritical annealing (IA) heat treatments were optimized to produce dual phase steels of similar martensite volume fraction, but with respectively isolated and continuous martensite distribution. The tensile and dynamic fracture properties of dual phase steels were investigated. Strain distribution of steels was measured by digital image correlation (DIC) method. Combined with observations of microcracks/microvoids, different deformation and fracture mechanisms were revealed. Compared to IA steel, SQ steel has lower strength, but longer elongation and higher fracture toughness, and the latter were attributed to larger deformation in ferrites that results in more stress relaxation of martensite during deformation. While in IA steel, the deformation in ferrites is blocked by adjacent martensites, so that a relatively small strain of ferrite cannot effectively relax the stress in martensites, which resulted in higher plastic deformation in martensite than in SQ steel; therefore, cracks preferentially initiate in martensite, and IA steel exhibits higher strength and lower plasticity.
引用
收藏
页码:1092 / 1100
页数:9
相关论文
共 26 条
[1]   Effect of Martensite Morphology on Tensile Deformation of Dual-Phase Steel [J].
Ahmad, E. ;
Manzoor, T. ;
Ziai, M. M. A. ;
Hussain, N. .
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2012, 21 (03) :382-387
[2]   Influence of martensite content and morphology on tensile and impact properties of high-martensite dual-phase steels [J].
Bag, A ;
Ray, KK ;
Dwarakadasa, ES .
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1999, 30 (05) :1193-1202
[3]   TENSILE PROPERTIES AND INHOMOGENEOUS DEFORMATION OF FERRITE MARTENSITE DUAL-PHASE STEELS [J].
BYUN, TS ;
KIM, IS .
JOURNAL OF MATERIALS SCIENCE, 1993, 28 (11) :2923-2932
[4]   Deformation and fracture mechanisms in fine- and ultrafine-grained ferrite/martensite dual-phase steels and the effect of aging [J].
Calcagnotto, Marion ;
Adachi, Yoshitaka ;
Ponge, Dirk ;
Raabe, Dierk .
ACTA MATERIALIA, 2011, 59 (02) :658-670
[5]   Influence of martensite morphology on the work-hardening behavior of high strength ferrite-martensite dual-phase steel [J].
Das, Debdulal ;
Chattopadhyay, Partha Protim .
JOURNAL OF MATERIALS SCIENCE, 2009, 44 (11) :2957-2965
[6]  
Gao L, 2009, P 7 CHIN STEEL C, P96
[7]  
Gerbase J., 1979, STRUCTURE PROPERTIES, P118
[8]   Local plastic strain evolution in a high strength dual-phase steel [J].
Ghadbeigi, H. ;
Pinna, C. ;
Celotto, S. ;
Yates, J. R. .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2010, 527 (18-19) :5026-5032
[9]   Quantitative measurement of strain partitioning and slip systems in a dual-phase steel [J].
Han, Qihang ;
Kang, Yonglin ;
Hodgson, Peter D. ;
Stanford, Nicole .
SCRIPTA MATERIALIA, 2013, 69 (01) :13-16
[10]  
Heat Treatment Manual Editorial Committee in Heat Treatment Institute of Chinese Mechanical Engineering Society, 2001, HEAT TREATM MAN, VI, P131