Numerical simulation of hybrid joining processes: self-piercing riveting combined with adhesive bonding

被引:13
|
作者
Potgorschek, Lukas [1 ]
Domitner, Josef [1 ]
Hoensch, Florian [2 ]
Sommitsch, Christof [1 ]
Kaufmann, Stefan [2 ]
机构
[1] Graz Univ Technol, Inst Mat Sci Joining & Forming, Res Grp Tools Forming, Inffeldgasse 11-1, A-8010 Graz, Austria
[2] Magna Steyr Fahrzeugtech AG & Co KG, Liebenauer Hauptstr 317, A-8041 Graz, Austria
来源
23RD INTERNATIONAL CONFERENCE ON MATERIAL FORMING | 2020年 / 47卷
关键词
Hybrid joining; Self-piercing riveting; SPR; Adhesive; Riv-bonding; FE simulation; TECHNOLOGIES;
D O I
10.1016/j.promfg.2020.04.322
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
Reliable simulation of hybrid joining processes using conventional finite element (FE) tools is challenging, because the liquid adhesive must be somehow included in the model. Thus, in this work the viscoelastic properties of the adhesive are substituted with "equivalent" mechanical properties. The complex viscosity of an epoxy-based single-component adhesive was determined at five temperatures between 20-55 C and at seven shear rates between 1-150 s- using a rheometer. Flow stresses and strain rates were calculated from the complex viscosities and from the shear rates. For each temperature investigated the relationship between flow stress and strain rate was fitted with a power-law, which enables modeling the actually liquid adhesive as solid with strain rate-dependent flow stress. In order to validate the material model, a defined volume of adhesive was uniaxially compressed. This testing setup was also modelled using the FE software Simufact Forming 15. In the model the Young's modulus of the adhesive was iteratively adapted until good agreement between the numerical and the experimental force-displacement curves was achieved. The obtained mechanical properties were finally used for modeling the adhesive layer between two 2.0 mm-thick 6xxx aluminum alloy blanks in the hybrid riveting-bonding process. An axisymmetric model including deformable (rivet, upper blank, lower blank, adhesive layer) and rigid (punch, die, blankholder) components was built in Simufact Forming. The cross-section of the hybrid joint obtained from simulation showed very good geometrical agreement with cross-sections obtained from the joining experiments, and just small differences between the calculated and the measured force-displacement curves was observed. (C) 2020 The Authors. Published by Elsevier Ltd. This is an open access article under the CC BY-NC-ND license (https/creativecommons.org/licenses/by-nc-nd/4.0/) Peer-review under responsibility of the scientific committee of the 23rd International Conference on Material Forming.
引用
收藏
页码:413 / 418
页数:6
相关论文
共 50 条
  • [21] Joining of aluminium using self-piercing riveting: Testing, modelling and analysis
    Porcaro, R
    Hanssen, AG
    Aalberg, A
    Langseth, M
    INTERNATIONAL JOURNAL OF CRASHWORTHINESS, 2004, 9 (02) : 141 - 154
  • [22] Joining of Polymer-Metal Lightweight Structures Using Self-Piercing Riveting (SPR) Technique: Numerical Approach and Simulation Results
    Amro, Elias
    Kouadri-Henni, Afia
    PROCEEDINGS OF 21ST INTERNATIONAL ESAFORM CONFERENCE ON MATERIAL FORMING (ESAFORM 2018), 2018, 1960
  • [23] Self-piercing riveting-a review
    Dezhi Li
    Andreas Chrysanthou
    Imran Patel
    Geraint Williams
    The International Journal of Advanced Manufacturing Technology, 2017, 92 : 1777 - 1824
  • [24] Developing a self-piercing riveting with flange pipe rivet joining aluminum sheets
    Huang, Zhichao
    Yao, Qiuhua
    Lai, Jiamei
    Zhao, Jingwei
    Jiang, Zhengyi
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2017, 91 (5-8): : 2315 - 2328
  • [25] A framework for calibration of self-piercing riveting process simulation model
    Fang, Yudong
    Huang, Li
    Zhan, Zhenfei
    Huang, Shiyao
    Liu, Xiongjie
    Chen, Qiuren
    Zhao, Hailong
    Han, Weijian
    JOURNAL OF MANUFACTURING PROCESSES, 2022, 76 : 223 - 235
  • [26] Self-piercing riveting-a review
    Li, Dezhi
    Chrysanthou, Andreas
    Patel, Imran
    Williams, Geraint
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2017, 92 (5-8): : 1777 - 1824
  • [27] Force characteristics of self-piercing riveting
    Kim, Dae-Wook
    Xu, Jun
    Li, Wei
    Blake, D.
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 2006, 220 (08) : 1259 - 1266
  • [28] Developing a self-piercing riveting with flange pipe rivet joining aluminum sheets
    Zhichao Huang
    Qiuhua Yao
    Jiamei Lai
    Jingwei Zhao
    Zhengyi Jiang
    The International Journal of Advanced Manufacturing Technology, 2017, 91 : 2315 - 2328
  • [29] Simulation and analysis of self-piercing riveting process in aluminum sheets
    Key Laboratory for Advanced Manufacturing by Materials Processing Technology, Department of Mechanical Engineering, Tsinghua University, Beijing 100084, China
    Cailiao Kexue yu Gongyi, 2007, 5 (713-717):
  • [30] Inversion Model of Maximum Riveting Force in Aluminum Alloy Self-piercing Riveting Processes
    Sun, Xiaoting
    Zeng, Kai
    He, Xiaocong
    Xing, Baoying
    Zhongguo Jixie Gongcheng/China Mechanical Engineering, 2021, 32 (11): : 1341 - 1345