Micro-liter lubrication machining of Inconel 718

被引：83

作者：

Obikawa, Toshiyuki ^{[1
]}

Kamata, Yasuhiro ^{[1
]}

Asano, Yuki ^{[2
]}

Nakayama, Kousuke ^{[2
]}

Otieno, Andrew W. ^{[3
]}

机构：

[1] Univ Tokyo, Inst Ind Sci, Meguro Ku, Tokyo 1538505, Japan

[2] Tokyo Inst Technol, Dept Mech & Control Engn, Tokyo 1528552, Japan

[3] No Illinois Univ, Dept Technol, De Kalb, IL 60115 USA

来源：

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE | 2008年 / 48卷 / 15期

基金：

日本学术振兴会;

关键词：

MQL machining; Inconel; 718; Control of oil-mist flow;

D O I：

10.1016/j.ijmachtools.2008.07.011

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Minimum quantity lubrication (MQL) machining is one of the promising solutions to the requirement for decrease in cutting fluid consumption. This paper describes MQL machining in a range of oil consumption <1.0ml/h, which is 10-100 times smaller than the consumption usually adopted in industries. MQL machining in this range is called micro-liter lubrication machining in this paper. A specially designed nozzle was used for concentrating small amounts of oil mist onto the cutting interface. The performance of concentrated spraying of oil mist in micro-liter lubrication machining of Inconel 718 was investigated and compared with that of ordinary spraying. This proved that the concentrated spraying of oil mist with a specially designed nozzle was quite effective in increasing tool life in the micro-liter lubrication range. (C) 2008 Elsevier Ltd. All rights reserved.

引用

页码：1605 / 1612

页数：8

共 16 条

[1]

Childs T.H.C., 2000, METAL MACHINING THEO

[2] An experimental investigation on effect of minimum quantity lubrication in machining AISI 1040 steel [J].

Dhar, N. R. ;

Ahmed, M. T. ;

Islam, S. .

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2007, 47 (05) :748-753

[3] Multilayered and nanolayered hard nitride thin films deposited by cathodic arc evaporation. Part 2: Mechanical properties and cutting performances [J].

Ducros, C. ;

Sanchette, F. .

SURFACE & COATINGS TECHNOLOGY, 2006, 201 (3-4) :1045-1052

[4] A review of developments towards dry and high speed machining of Inconel 718 alloy [J].

Dudzinski, D ;

Devillez, A ;

Moufki, A ;

Larrouquère, D ;

Zerrouki, V ;

Vigneau, J .

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2004, 44 (04) :439-456

[5] Dry and semi-dry machining using finely crystallized diamond coating cutting tools [J].

Hanyu, H ;

Kamiya, S ;

Murakami, I ;

Saka, M .

SURFACE & COATINGS TECHNOLOGY, 2003, 174 :992-995

[6] Effect of MQL on the tool life of small twist drills in deep-hole drilling [J].

Heinemann, R ;

Hinduja, S ;

Barrow, G ;

Petuelli, G .

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2006, 46 (01) :1-6

[7] High speed MQL finish-turning of Inconel 718 with different coated tools [J].

Kamata, Y. ;

Obikawa, T. .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2007, 192 :281-286

[8]

KAMATA Y, 2005, THESIS TOKYO I TECHN

[9] Effect of coolant strategy on tool performance, chip morphology and surface quality during high-speed machining of A356 aluminum alloy [J].

Kishawy, HA ;

Dumitrescu, M ;

Ng, EG ;

Elbestawi, MA .

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2005, 45 (02) :219-227

[10] Feasibility study of the minimum quantity lubrication in high-speed end milling of NAK80 hardened steel by coated carbide tool [J].

Liao, Y. S. ;

Lin, H. M. ;

Chen, Y. C. .

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2007, 47 (11) :1667-1676

← 1 2 →