Effect of subgrain structure on the creep strength of alloy 1207

被引：3
作者：
Dudko, V. A. [1 ]
Kaibyshev, R. O. [1 ]
Salakhova, E. R. [2 ]
机构：
[1] Belgorod State Univ, Belgorod 308015, Russia
[2] Ufa State Aviat Tech Univ, Ufa 450000, Russia
来源：
PHYSICS OF METALS AND METALLOGRAPHY | 2009年 / 107卷 / 01期
关键词：
MG-SC ALLOY; DEFORMATION-BEHAVIOR; THRESHOLD STRESS; AL;
D O I：
10.1134/S0031918X09010128
中图分类号：
TF [冶金工业];
学科分类号：
0806 ;
摘要：
The effect of severe plastic deformation (SPD) on the creep resistance of the Al-6%Cu-0.48Mn-0.52Mg-0.3Sc-0.1Zr alloy has been examined in a temperature range of 125-180A degrees C. It has been shown that SPD performed by the method of equal-channel angular pressing at 300A degrees C to a true strain of similar to 1 leads to the formation of a well-defined subgrain structure, which is retained upon solution treatment before quenching because of the presence in the alloy of ultradisperse Al(3)(Sc, Zr) particles with coherent boundaries. It was established that the creep strength at 125-150A degrees C of the as-cast alloy and of the deformed material is approximately the same. At 180A degrees C, the creep rate of the deformed aluminum alloy is almost an order of magnitude lower than that of the as-cast alloy. The reasons for the influence of the subgrain structure on the creep strength of the Al-Cu-Sc-Zr alloy are discussed.
引用
收藏
页码：90 / 95
页数：6
相关论文
共 18 条
  • [1] ABE F, 2001, P 3 INT C ADV MAT TE, P79
  • [2] The threshold stress in a rapidly solidified Al-5Cr-2Zr alloy
    Brahmi, A
    Gerique, T
    Torralba, M
    Lieblich, M
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1998, 246 (1-2): : 55 - 60
  • [3] Cadek J., 1988, CREEP METALIC MAT
  • [4] Creep behavior and threshold stress of an extruded Al-6Mg-2Sc-1Zr alloy
    Deshmukh, SP
    Mishra, RS
    Kendig, KL
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2004, 381 (1-2): : 381 - 385
  • [5] Evans R.W., 1985, CREEP METALS ALLOYS
  • [6] Continuous dynamic recrystallization in an Al-Li-Mg-Sc alloy during equal-channel angular extrusion
    Kaibyshev, R
    Shipilova, K
    Musin, F
    Motohashi, Y
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2005, 396 (1-2): : 341 - 351
  • [7] Deformation behavior of a modified 5083 aluminum alloy
    Kaibyshev, R
    Musin, F
    Avtokratova, E
    Motohashi, Y
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2005, 392 (1-2): : 373 - 379
  • [8] Deformation behavior of a 2219 Al alloy
    Kaibyshev, R
    Sitdikov, O
    Mazurina, I
    Lesuer, DR
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2002, 334 (1-2): : 104 - 113
  • [9] Creep behavior and microstructural stability of Al-Cu-Mg-Ag and Al-Cu-Li-Mg-Ag alloys
    Kazanjian, SM
    Wang, N
    Starke, EA
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1997, 234 : 571 - 574
  • [10] An investigation of creep and substructure formation in 2124 Al
    Li, Y
    Nutt, SR
    Mohamed, FA
    [J]. ACTA MATERIALIA, 1997, 45 (06) : 2607 - 2620
12