Development of high strength ductile hypereutectoid steel by cyclic heat treatment process

被引:39
|
作者
Saha, Atanu [2 ,3 ]
Mondal, Dipak Kumar [1 ]
Biswas, Koushik [4 ]
Maity, Joydeep [1 ]
机构
[1] Natl Inst Technol Durgapur, Dept Met & Mat Engn, Durgapur 713209, W Bengal, India
[2] CSIR Cent Mech Engn Res Inst, NDT, Durgapur 713209, W Bengal, India
[3] CSIR Cent Mech Engn Res Inst, Met Grp, Durgapur 713209, W Bengal, India
[4] Indian Inst Technol, Dept Met & Mat Engn, Kharagpur 721302, W Bengal, India
关键词
Hypereutectoid steel; Cyclic heat treatment; Lamellar faults; Fragmentation and thickening of cementite lamella; Divorced eutectoidal reaction; Cementite plates and spheroids; Strength and ductility; DISLOCATION INTERPHASE BOUNDARIES; TRANSFORMATION TEMPERATURE; MECHANICAL-PROPERTIES; PEARLITIC STEELS; CARBON-STEELS; KINK MOTION; MICROSTRUCTURE; SPHEROIDIZATION; MIGRATION; AUSTENITE;
D O I
10.1016/j.msea.2012.02.026
中图分类号
TB3 [工程材料学];
学科分类号
0805 ; 080502 ;
摘要
In this work a homogenizing annealed 1.24 wt% carbon steel was subjected to cyclic heat treatment process that consisted of repeated short-duration (6 min) holding at 894 degrees C (above Acm temperature) followed by forced air cooling. During short-duration holding at 894 degrees C. fragmentation (owing to partial dissolution) and thickening of cementite lamella occurred at the preferred high energy sites of lamellar faults. These undissolved fragmented cementite acted as pre-existing nuclei promoting the divorced eutectoidal reaction (DET) during forced air cooling that generated non lamellar region (NLR) in the microstructure apart from the presence of lamellar pearlite region (LPR) and cementite network (CN). The CN was also fragmented with repeated holding and cooling cycles. Besides, new lamellar fault sites were generated during forced air cooling to promote lamellar fragmentation. Accordingly, as the number of heat treatment cycles increases, more uniformly dispersed finer cementite particles (pre-existing nuclei) in austenite matrix was obtained at 894 degrees C. Therefore, the proportion of NLR increased and the proportions of LPR and CN decreased with the progress of cyclic heat treatment. After 8 cycles of heat treatment the microstructure mostly consisted of a combination of spheroids (0.55 +/- 0.24 mu m in size) and non-spheroids (mainly the plate shaped particles of 0.22 +/- 0.10 mu m in size) of cementite in 1:5 proportion by area% dispersed in ferrite matrix. The generation of cementite plates occurred through the motion of transformation disconnections. This provided an excellent combination of strength (UTS = 1086 MPa) and ductility (%elongation = 13) in this 1.24 wt% C steel. The property obtained had similarity to what was reported for a thermo-mechanically processed steel of much higher carbon content (1.8 wt%) where the microstructure consisted of solely the cementite spheroids of 0.65 mu m average size dispersed in ferrite matrix. (C) 2012 Elsevier B.V. All rights reserved.
引用
收藏
页码:204 / 215
页数:12
相关论文
共 50 条
  • [41] New heat treatment process for advanced high-strength steels
    Bublikova, D.
    Jenicek, S.
    Vorel, I.
    Masek, B.
    4TH INTERNATIONAL CONFERENCE RECENT TRENDS IN STRUCTURAL MATERIALS, 2017, 179
  • [42] Development of high strength and ductile martensitic stainless steel coatings with Nb addition fabricated by laser cladding
    Li B.C.
    Zhu H.M.
    Qiu C.J.
    Zhang D.K.
    Journal of Alloys and Compounds, 2021, 832
  • [43] Development of high strength and ductile martensitic stainless steel coatings with Nb addition fabricated by laser cladding
    Li, B. C.
    Zhu, H. M.
    Qiu, C. J.
    Zhang, D. K.
    JOURNAL OF ALLOYS AND COMPOUNDS, 2020, 832
  • [44] DEVELOPMENT OF HIGH STRENGTH STEEL PLATES FOR LARGE HEAT INPUT WELDING.
    Kawaguchi, Yoshiaki
    Yamaguchi, Yoji
    Ohtani, Hiroo
    Watanabe, Seiichi
    Sumitomo Metals, 1978, 30 (01): : 15 - 30
  • [45] Surface morphologies and microstructure of high-strength steel AISI 4820 with different heat treatment during grinding process
    Zhong, Bingfu
    Dang, Jiaqiang
    An, Qinglong
    Chen, Ming
    JOURNAL OF MANUFACTURING PROCESSES, 2023, 96 : 1 - 10
  • [46] Processing and characterization of high strength dual-phase steel by two-step intercritical heat treatment process
    Singh, Praveen
    Singh, Satnam
    Mewar, Sanchit
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART E-JOURNAL OF PROCESS MECHANICAL ENGINEERING, 2019, 233 (03) : 581 - 588
  • [47] Effect of High-Temperature Thermomechanical Treatment on Cyclic Strength of Spring Steel.
    Bernshtein, M.L.
    Zhadan, V.T.
    Khensger, K.E.
    Problemy Prochnosti, 1973, 5 (12): : 40 - 43
  • [48] Optimization of heat treatment conditions for maximum toughness of high strength silicon steel
    Barbacki, A
    Mikolajski, E
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 1998, 78 (1-3) : 18 - 23
  • [49] EFFECT OF METHOD OF MELTING AND OF HEAT TREATMENT ON FATIGUE STRENGTH OF HIGH TENSILE STEEL
    GUREVICH, SE
    ODING, IA
    RUSSIAN METALLURGY, 1965, (04): : 66 - &
  • [50] Novel gusset plate design using high strength steel and heat treatment
    Mohammadi, Hossein
    Becker, Tracy C.
    Zurob, Hatem
    JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH, 2019, 157 : 59 - 69