Development of high strength ductile hypereutectoid steel by cyclic heat treatment process

被引:39
|
作者
Saha, Atanu [2 ,3 ]
Mondal, Dipak Kumar [1 ]
Biswas, Koushik [4 ]
Maity, Joydeep [1 ]
机构
[1] Natl Inst Technol Durgapur, Dept Met & Mat Engn, Durgapur 713209, W Bengal, India
[2] CSIR Cent Mech Engn Res Inst, NDT, Durgapur 713209, W Bengal, India
[3] CSIR Cent Mech Engn Res Inst, Met Grp, Durgapur 713209, W Bengal, India
[4] Indian Inst Technol, Dept Met & Mat Engn, Kharagpur 721302, W Bengal, India
关键词
Hypereutectoid steel; Cyclic heat treatment; Lamellar faults; Fragmentation and thickening of cementite lamella; Divorced eutectoidal reaction; Cementite plates and spheroids; Strength and ductility; DISLOCATION INTERPHASE BOUNDARIES; TRANSFORMATION TEMPERATURE; MECHANICAL-PROPERTIES; PEARLITIC STEELS; CARBON-STEELS; KINK MOTION; MICROSTRUCTURE; SPHEROIDIZATION; MIGRATION; AUSTENITE;
D O I
10.1016/j.msea.2012.02.026
中图分类号
TB3 [工程材料学];
学科分类号
0805 ; 080502 ;
摘要
In this work a homogenizing annealed 1.24 wt% carbon steel was subjected to cyclic heat treatment process that consisted of repeated short-duration (6 min) holding at 894 degrees C (above Acm temperature) followed by forced air cooling. During short-duration holding at 894 degrees C. fragmentation (owing to partial dissolution) and thickening of cementite lamella occurred at the preferred high energy sites of lamellar faults. These undissolved fragmented cementite acted as pre-existing nuclei promoting the divorced eutectoidal reaction (DET) during forced air cooling that generated non lamellar region (NLR) in the microstructure apart from the presence of lamellar pearlite region (LPR) and cementite network (CN). The CN was also fragmented with repeated holding and cooling cycles. Besides, new lamellar fault sites were generated during forced air cooling to promote lamellar fragmentation. Accordingly, as the number of heat treatment cycles increases, more uniformly dispersed finer cementite particles (pre-existing nuclei) in austenite matrix was obtained at 894 degrees C. Therefore, the proportion of NLR increased and the proportions of LPR and CN decreased with the progress of cyclic heat treatment. After 8 cycles of heat treatment the microstructure mostly consisted of a combination of spheroids (0.55 +/- 0.24 mu m in size) and non-spheroids (mainly the plate shaped particles of 0.22 +/- 0.10 mu m in size) of cementite in 1:5 proportion by area% dispersed in ferrite matrix. The generation of cementite plates occurred through the motion of transformation disconnections. This provided an excellent combination of strength (UTS = 1086 MPa) and ductility (%elongation = 13) in this 1.24 wt% C steel. The property obtained had similarity to what was reported for a thermo-mechanically processed steel of much higher carbon content (1.8 wt%) where the microstructure consisted of solely the cementite spheroids of 0.65 mu m average size dispersed in ferrite matrix. (C) 2012 Elsevier B.V. All rights reserved.
引用
收藏
页码:204 / 215
页数:12
相关论文
共 50 条
  • [31] Understanding ductile fracture characteristics of an advanced high strength steel
    Das, Arpan
    MATERIALS LETTERS, 2025, 387
  • [32] Development of high ductile ultra high strength structural steel through stabilization of retained austenite and stacking fault
    Poddar, Debasis
    Ghosh, Chiradeep
    Bhattacharya, Basudev
    Singh, Vivek Kumar
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2019, 762
  • [33] ON DEVELOPMENT OF HIGH STRENGTH IN STEEL
    COHEN, M
    JOURNAL OF THE IRON AND STEEL INSTITUTE, 1963, 201 (10): : 833 - &
  • [34] A high-strength steel with good ductile values: Development of a new steel for the reduction of weight and costs in automotive engineering
    Doppler, Georg
    Kinsinger, Volker
    Klein, Heinz Willi
    Peipe, Hartmut
    Eisenberg, Stephan
    Achmus, Christian
    HTM - Journal of Heat Treatment and Materials, 1998, 53 (04): : 259 - 264
  • [35] DEVELOPMENT OF HIGH TENSILE STRENGTH STEEL PLATE FOR HIGH HEAT INPUT WELDING.
    Furusawa, Jun
    Arimochi, Kazushige
    Kurayasu, Hirofumi
    Nakano, Naokazu
    Suzuki, Shu-ichi
    Sumitomo Metals, 1988, 40 (01): : 39 - 48
  • [36] Microstructural assessment of AISI 1021 steel under rapid cyclic heat treatment process
    Adeleke, A. A.
    Ikubanni, P. P.
    Orhadahwe, T. A.
    Aweda, J. O.
    Odusote, J. K.
    Agboola, O. O.
    RESULTS IN ENGINEERING, 2019, 4
  • [37] Ultrahigh strength ductile microalloyed steel with a very low yield ratio developed by quenching and partitioning heat treatment
    S. Fida Hassan
    H. AlWadei
    Scientific Reports, 12
  • [38] Ultrahigh strength ductile microalloyed steel with a very low yield ratio developed by quenching and partitioning heat treatment
    Hassan, S. Fida
    AlWadei, H.
    SCIENTIFIC REPORTS, 2022, 12 (01)
  • [39] Simultaneous enhancement of ductility and strength in AISI 1080 steel through a typical cyclic heat treatment
    Mishra, Shakti
    Mishra, Alok
    Show, Bijay Kumar
    Maity, Joydeep
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2017, 688 : 262 - 271