INVESTIGATING THE EFFECTS OF CUTTING PARAMETERS ON THE BUILT-UP-LAYER AND BUILT-UP-EDGE FORMATION DURING THE MACHINING OF AISI 310 AUSTENITIC STAINLESS STEELS

被引：13

作者：

Bilgin, Mehmet Burak ^{[1
]}

机构：

[1] Amasya Univ, Fac Technol, Dept Mech Engn, Amasya, Turkey

来源：

MATERIALI IN TEHNOLOGIJE | 2015年 / 49卷 / 05期

关键词：

built-up edge; built-up layer; machining; stainless steels; INCONEL; 718; ALUMINUM-ALLOYS; TOOL; WEAR; MACHINABILITY;

D O I：

10.17222/mit.2014.253

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

This study experimentally investigated the effects of machining parameters on the built-up-layer (BUL) and built-up-edge (BUE) formation and the wear behavior of cutting tools during the machining of the AISI 310 austenitic stainless steel with titanium-carbide cutting tools. Five different cutting speeds (50, 75, 100, 125 and 150) m/min, three feed rates (0.15, 0.20 and 0.25) mm/r and two cutting depths (1.5, 2) mm were used as the cutting parameters. The highest accumulation of the BUL and the BUE was observed at a cutting speed of 50 m/min, a feed rate of 0.15 mm/r and a cutting depth of 1.5 mm.

引用

页码：779 / 784

页数：6

共 16 条

[1]

Carrilero M.S., 1996, J. Mech. Behav. Mater, V7, P179, DOI [10.1515/JMBM.1996.7.3.179, DOI 10.1515/JMBM.1996.7.3.179]

[2] A SEM and EDS insight into the BUL and BUE differences in the turning processes of AA2024 Al-Cu alloy [J].

Carrilero, MS ;

Bienvenido, R ;

Sánchez, JM ;

Alvarez, M ;

González, A ;

Marcos, M .

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2002, 42 (02) :215-220

[3] Wettability and machinability study of pure aluminium towards uncoated and coated carbide cutting tool inserts [J].

Chattopadhyay, A. K. ;

Roy, P. ;

Ghosh, A. ;

Sarangi, S. K. .

SURFACE & COATINGS TECHNOLOGY, 2009, 203 (08) :941-951

[4]

Gokkaya H., 2007, J FACULTY ENG ARCH G, V22, P481

[5] Analysis of the evolution of the Built-Up Edge and Built-Up Layer formation mechanisms in the dry turning of aeronautical aluminium alloys [J].

Gomez-Parra, A. ;

Alvarez-Alcon, M. ;

Salguero, J. ;

Batista, M. ;

Marcos, M. .

WEAR, 2013, 302 (1-2) :1209-1218

[6] Wear, cutting forces and chip characteristics when dry turning ASTM Grade 2 austempered ductile iron with PcBN cutting tools under finishing conditionsy [J].

Katuku, K. ;

Koursaris, A. ;

Sigalas, I. .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2009, 209 (05) :2412-2420

[7] Tool wear/life evaluation when finish turning Inconel 718 using PCBN tooling [J].

Khan, S. A. ;

Soo, S. L. ;

Aspinwall, D. K. ;

Sage, C. ;

Harden, P. ;

Fleming, M. ;

White, A. ;

M'Saoubi, R. .

FIFTH CIRP CONFERENCE ON HIGH PERFORMANCE CUTTING 2012, 2012, 1 :283-288

[8] Determination of optimum cutting parameters during machining of AISI 304 austenitic stainless steel [J].

Korkut, I ;

Kasap, M ;

Ciftci, I ;

Seker, U .

MATERIALS & DESIGN, 2004, 25 (04) :303-305

[9] Wear progression of carbide tool in low-speed end milling of stainless steel [J].

Liew, W. Y. H. ;

Ding, X. .

WEAR, 2008, 265 (1-2) :155-166

[10] Wear behaviour of cemented carbide tools in dry machining of aluminium alloy [J].

List, G ;

Nouari, M ;

Géhin, D ;

Gomez, S ;

Manaud, JP ;

Le Petitcorps, Y ;

Girot, F .

WEAR, 2005, 259 :1177-1189

← 1 2 →