Oxidation-assisted creep damage in a wrought nickel-based superalloy: Experiments and modelling

被引：58

作者：

Chateau, E. ^{[1
]}

Remy, L. ^{[1
]}

机构：

[1] Mines Paris Paristech, CNRS, UMR 7633, Ctr Mat, F-91003 Evry, France

来源：

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2010年 / 527卷 / 7-8期

关键词：

Creep; Nickel alloys; Oxidation; Precipitate coarsening; Constitutive equations; LOW-CYCLE FATIGUE; HIGH-TEMPERATURE ALLOYS; IN-100; SUPERALLOY; AIR-ENVIRONMENT; OXIDE SCALES; BEHAVIOR; PERFORMANCE; MECHANISMS; PREDICTION; THICKNESS;

D O I：

10.1016/j.msea.2009.10.054

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

Creep damage investigation was carried out in wrought nickel-based superalloy Udimet 720LI in air at 850 degrees C using multiple cross-sections specimens in order to be able to make interrupted tests. In all tests conducted on this material, creep curves showed only tertiary stage and the surface connected intergranular cracking was found to be dominant in creep fracture. It was shown that gamma' precipitate coarsening occurs in the bulk of the specimens and obeys the LSW kinetics. Metallographic analysis led to the conclusion that creep does not alter oxidation, except at grain boundaries, where oxide spikes can be developed under creep. Therefore grain boundary oxidation was found to be creep strain-assisted. A constitutive model accounting for precipitate coarsening was proposed. The oxidation-assisted intergranular damage and the oxidation embrittlement of the microstructure elements phenomena were successfully described using the continuum damage mechanics and the local ductility exhaustion laws, respectively. Creep rupture and elongation curves were taken into account by the model with suitable accuracy, as well. The model was found able to figure the specimen's geometry variations effects on lifetime and creep elongation curves. (C) 2009 Published by Elsevier B.V.

引用

页码：1655 / 1664

页数：10

共 51 条

[21]

Fredholm A., 1987, MONOCRISTAUX ALLIAGE

[22]

GIGGINS CS, 1969, T METALL SOC AIME, V245, P2495

[23] A QUANTITATIVE METALLOGRAPHIC ASSESSMENT OF STRUCTURAL DEGRADATION OF TYPE-316 STAINLESS-STEEL DURING CREEP-FATIGUE [J].

HALES, R .

FATIGUE OF ENGINEERING MATERIALS AND STRUCTURES, 1980, 3 (04) :339-356

[24]

HARADA H, 2003, COMPREHENSIVE STRUCT, V5, P361

[25] An experimental assessment of grain size effects in the uniaxial straining of thin Al sheet with a few grains across the thickness [J].

Janssen, PJM ;

de Keijser, TH ;

Geers, MGD .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2006, 419 (1-2) :238-248

[26] On the origin of the stress decrease for nickel polycrystals with few grains across the thickness [J].

Keller, C. ;

Hug, E. ;

Chateigner, D. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2009, 500 (1-2) :207-215

[27] CONSTITUTIVE EQUATIONS FOR CREEP-RUPTURE [J].

LECKIE, FA ;

HAYHURST, DR .

ACTA METALLURGICA, 1977, 25 (09) :1059-1070

[28] Analysis of creep curves of a nickel base superalloy in a wide stress/temperature range [J].

Maldini, M. ;

Angella, G. ;

Lupine, V. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2007, 462 (1-2) :436-440

[29]

MCMAHON CJ, 1970, METALL TRANS, V1, P3443

[30]

OSGERBY S, 1990, MATER SCI TECH SER, V6, P2, DOI 10.1179/026708390790189443

← 1 2 3 4 5 6 →